REQUEST FOR PROPOSAL NO. RD-12-66 'ADVANCED REAR PROJECTION VIEWER'
Document Type:
Collection:
Document Number (FOIA) /ESDN (CREST):
CIA-RDP78B04770A001900020009-2
Release Decision:
RIPPUB
Original Classification:
K
Document Page Count:
6
Document Creation Date:
December 28, 2016
Document Release Date:
February 23, 2005
Sequence Number:
9
Case Number:
Publication Date:
August 11, 1966
Content Type:
LETTER
File:
Attachment | Size |
---|---|
![]() | 176.92 KB |
Body:
Approved For~Release 2005/05/02: CIA-RDP78B04770A0019000200
In Reply Refer To: T 7 -
9965-3302
11 August 1966
os ice ox
Southwest Station
Washington, D.C. 20024
Reference:. 1 Letter T3410-66-24 dated
2? January 1966
2~Report 65-184, Advanced Rear
Projection Viewer dated December 1965
3) Your document, "Additional Specifications
To Be Included In The Development Of An
Advanced Rear Projection Viewer"
4) Letter T3410-66-135 dated
14 April 1966
Report 65-184, Amendment to Advanced
Rear Projection Viewer, July 1966
(3 copies)
Subject: Request For Proposal No. RD-12-66
"Advanced Rear Projection Viewer11
The reference 1) letter stated that would be willing to
negotiate a fixed price contract upon agreement of mutually accept-
able specific performance requirements for the subject Rear Pro-
jection Viewer. As a result of the meeting of 7 April 1966, essen-
tial agreement has been reached on these requirements. Further
development of the Rear Projection Viewer that is pro-
ducing for the Strategic Air Command has brought us to the point
where we can now offer this program on a fixed price basis.
References 2) through 4) and the enclosure constitute a complete
statement of the performance specifications of the Viewer.
price for this equipment is
.~ STAT
ra~~3 ~ `'
STAT
STAT
STAT
STAT
Declass Review by NGA.
Approved For Release 2005/05/02: CIA-RDP78B04770A001900020009-2
Approved For~f elease 2005/05/02: CIA-RDP78B04770~A001900020009-2
T3774-0046
9965-3302
11 August 1966
This proposed price is based u on amortization of estimated development
costs over ten units. will accumulate these costs in a
separately identifiable pool. The unit price of subsequent units (up
to a total of ten) will be determined based on their pro-rata share of
these development costs.
References 2) through 4) and the enclosure present the technical ap-
proach, equipment description, performance and delivery schedule
proposed for the successful accomplishment of the program. These
documents are an integral part of offer and are incorporated
proposal is based on the following assumptions and conditions:
1. Acce tance testing will be based upon the performance specifications.
will prepare an Acceptance Test Procedure as part of this
program and submit it for customer approval prior to testing.
2. Delivery shall be F.O.B, destination.
3. Quality of the equipment shall be best commercial practice.
4. Other mutually acceptable terms and conditions based upon the Armed
Services Procurement Regulations, including Progress Payments.
5. Go-ahead by no later than 30 September 1966.
6. reserves the right to revise this proposal at any time
up to t e time of negotiation.
We appreciate the opportunity to submit this proposal and look forward
to participating in the program. If additional information is re-
quired, please contact
Very truly yours,
AWB:gc
Approved For Release 2005/05/02: CIA-RDP78B04770A001900020009-2
Approved For Release 2005/05/02 :CIA-RDP78B04770A001900020009-2
Approved For Release 2005/05/02 :CIA-RDP78B04770A001900020009-2
Approved Fo~elease 2005/05/02 :CIA-RDP78B047 OA001900020009-2
A device to facilitate film threading in the Screening Viewer will consist of a
-clear Mylar film leader and a specially constructed, single flange take-up reel
(see illustration).
NOTE: FILM TRANSPQRT STRUCTURE
OMITTED FOR CLARITY.
REFER TO FIGURE 3-12.
THREADING
LEADER
LEA DER
CENTERING
SLIT
Approved For Release 2005/05/01 :CIA-RDP78B04770A001900020009-2
Approved For I~~lease 2005/05/02: CIA-RDP78B04770,~A 01900020009-2
In oper~~tion, the leader will be attached with tape to the start of film on the
feed reel, and the film is then wound on the take-up reel during the screening
process. Since the width of film that may be used in screening is infinitely
variable from 70 mm to 9 1/2 inches, the width of the leader will be that of the
narrowest film (70 mm). The operator will be able to position the leader on the
take-up reel so that the leader is approximately centered on the film, thus pre-
venting a tapered cylinder effect.
The single flange take-up reel concept is in constant use by the motion picture
industry, where up to 3000 feet of 35-mm film is wound at speeds of 600 feet per
minute without adverse effects. The only prerequisite for this type of operation
is good alignment of the take-up reel core in respect to film motion.
The threading device will be interchangeable with the AF Standard 51C17848 spool,
which will allow the operator to use the Screening Viewer in a conventional reel-
to-reel mode.
The leader will consist of a 48-inch long, 70-mm wide, 0.003- to 0.005-inch thick
clear Mylar film and a cylindrical clamp. One end will terminate in a split cyl-
inder which will clamp the Mylar strip and serve as an anchor inside the take-up
reel hub. The other end of the leader will be attached to the film supply with
tape.
The take-up reel will consist of a 2-inch diameter hub, 9 1/2 inches long, with a
10 1/2-inch diameter flange at one end. The hub will be made with a slit to allow
the leader to be moved in or out until it lies flat against the guide rollers.
Approved For Release 2005/05/02 CIA-RDP78B04770A001900020009-2
Approved Fordelease 2005/05/02: CIA-RDP78B04770A001900020009-2
The mensuration system for the Advanced Rear Projection Viewer will enable the
operator.to measure film distances (along the film) in 1-mm increments over a
distance of 40 inches or more.
The system will consist of a metering roller, a rotary photoelectric pulser, and
an electronic counter indicator mounted on a control panel. The metering roller is
one of the film guide rollers on the transport.
The system will be provided in lieu of the footage counter.
DETAILED DESCRIPTION
Metering Roller
The low inertia roller will provide input for the photoelectric pulser, with its
circumference being equal to 120 mm (1.5 diameter, approximate).
Photoelectric Pulser
The direction sensitive pulser will be directly driven by the metering roller shaft.
Each revolution will provide 120 signal pulses for the electronic counter.
Electronic Counter Indicator
The up-down counter will consist of electronic components which accept the pulses
from the rotary pulser and indicate the accumulated count on a 5-digit and sign
(PLUS or MINUS) display. A pushbutton zero-reset will be located on the control
panel.
Approved For Release 2005/05/023 CIA-RDP78B04770A001900020009-2