CONTRACT(Sanitized)REFERENCE CUSTOMER LETTER OF 4 JANUARY 1971 ON LIGHT TABLE DEFECTS.
Document Type:
Collection:
Document Number (FOIA) /ESDN (CREST):
CIA-RDP78B05171A000400030115-3
Release Decision:
RIPPUB
Original Classification:
K
Document Page Count:
12
Document Creation Date:
December 28, 2016
Document Release Date:
June 7, 2005
Sequence Number:
115
Case Number:
Publication Date:
January 8, 1971
Content Type:
TELEGRAM
File:
Attachment | Size |
---|---|
![]() | 1.02 MB |
Body:
Approved For Rele
jf4
r2117n
se 2005/06/23: CIA-RDP78B0517111y0400030115-3
1911 JAN 8 AlA 10 0
CJ AX008 (L IWA391) NL PDB TDIW FAX LOS ANGELES CALIF JAN 7
WESTERN UNION"ATTN TELEPHONE 524-6654
WILL CALL 3109 WILSON BLVD ARLINGTON VIP.
ST EJECT:
ST
C17
rr-1
REFERENCE CUSTOMER LETTER OF 4 JANUARY_
1971 ON LIGHT TABLE DEFECTS. 1. WE SUBMIT THAT NO SAFETY, HAZARD,
EXISTS. OTHERWISE WE WOULDHAVE ALTERED TABLE-:DESIGN. THIS.
FIRST UNIT WAS *ROUGHLY EXAMINED BY YOUR PERSONNEL IN LOS.
NGE14SIF YOU ELECT, WILL ACCEPT A SCOPE CHANGE. TO
CORRECT THE SITUATI.ON1.2.2T4IS FAULT APPEARS TO BE UNIQUE TO
TABLES/N001.9 AND .DOES- NOT 'APPEAR ON THE ATTACHMENT NOo'.2.REGARDING
THE INSPECTION OF 14 PRODUCTION TABLES. OUR FIELD .SERVICE REPRESENTATIVE
WILL INSPECT AND CORRECT THIS DEFICIENCY'ON S/NO01. 3. MS26565
'GP 3E(
Declass
Review by
NGAIDoD
DOES.NOT COVER THE DIMENSIONS OF A 6.6" REEL. ,
TOOK THE
POSITION THAT 6.6" FILM WIDTH BE IN EFFECT SUBSTITUTED FOR
THE 5" FILM T:YIDTH IN SAID STANDARD AND EXTROPOLATED APPROPRIATE
DIMENSIONS FROM THE 5" SPECIFICATION. THIS RESULTED IN A DESIGN
WHERE THE .MAXIMUM-TOLERANCED REEL WOULD BE NO GREATER THAN
60782-INCHES. THE PROTOTYPE'PREVIOUSLY DELIVERED AND EVALUATED
By YOU AND UNIT SERIAL 001 INSPECTED HERE IN LOS ANGELES BOTH
INCORPORATE THIS DESIGN.
UNDERSTANDS THAT CURRENT 6.6"
REELS AVAILABLE TO THE CUSTONER EXCEED THIS NUMBER AND THE
CRITICAL NATURE OF THIS PARAMETER. WE WILL IMMEDIATELY INSTITUTE
A CORRECTION WHICH IS FIELD RETROFITTABLE AND FACTORY IMPLEMENTED,
AND WILL SUBMIT A CLAIM COVERING THIS SCOPE CHANGE, 4.14emiw4451
Approved For Release 2005/06/23 : CIA-RDP78B05171A0
SUBMITS THAT THE TABLE COMPLETELY MEETS THE REQUIREMENTS OF
STAT
STA1
TAITGRAPHilt*46g--.1i-T.A6L' E4gLlr tIOYED;.11SIDE.
P4tkAltrii/A/IIRP.Vn41113860G1'15-:
Y. THE OtiERPITEYitPIOV.
CODING ON MOTORS IS MEANT ONLY AS A VISUAL REFERENCE: GUIDE
AND, THE PRECISE POSITIONING IS OBTAINED BY MECHANICAL:,DETENTING
IN WHICH AN OPERATOR CAN FEEL LOCK-IN. WHEN MOTORS ARE USED -
IN THE SPLIT VERTICAL MODE THIS VISUAL REFERENCE, CAN. BE OBTAINED
BY USING THE LEFT REAR MOTOR ON THE LOWER RIGHT POSITION AND
THE RIGHT REAR MOTOR ON THE LOWER_:LEFT POSITION. MOTORS ARE
EASILY INTERCHANGED BY SIMPLE PLUG-IN OPERATION..
THAT DESIGN MEETS THE REQUIREMENTS OF 3.3.1.2. 6.
-
SUBMITS STA-if
RECOGNIZES STA
EETHE CONDITION OF LOWER COVER BEING PREVENTED FROM OPENING WHEN
THE TABLE HAS SHIFTED IN ITS HORIZONTAL POSITION RELATIVE TO
CD THE ELEVATING STAND.' WE WILL MAKE AN IN-LINE CORRECTION TO
40
PREVENT THE TABLES FROM. AND. PROVIDE FIELD-INSTALLED
PLUGS TO HOLD:THE-TABLES;IN THE CORRECT ,POSITION. ? OPERATIONAL
PROCEDURES WILL REQUIRE THAT THE TABLE BE LOWERED' TO THE HORIZONTAL
. ,
POSITION. FOR LOADING THE IN-LINE InEwiNq OF TWOSIMILAR-WIDTH''
= FILMS. AND THIS IS A SIMPLE OPERATION. 7. 1ECOGNI2ES
m THE INCONVENIENCE OF THE TAKE-UP LOOP BEING BLOCKED IN ONE
2 DIRECTION DUE TO THE CABLE GUIDES,' AND WILL MAKE AN INLINE
CHANGE TO CORRECT THIS AND PROVIDE A. BASIS FOR FIELD RETROFIT.
S. THE LOCATION OF THE LOWER COVER LATCHES ARE THE RESULT OF:
A' DESIGN TRADE-OFF FOR SAFETY AND CONVENIENCE OF THE OPERATOR .
?..
ST
E.-
IN THE KNEEWELL AREA. SUBMITS THAT THE OPERATION IS 0!..
A SIMPLE ONE, IS NOT AN OPERATING CONTROL, AND IT MEETS THE )
REQUIREMENTS OF PARAGRAPH 3.2.1.4. 9. PROVISION HAS BEEN MADE:
FOR ADJUSTMENT BY FACTORY TRAINED PERSONNEL TO BALANCE THE
TWO ILLUMINATION SOURCES IN ORDER TO MEET THE REQUIREMENTS.
OF THE FIRST PORTION OF PARAGRAPH
"
WILL ENSURE STA1
THAT FACTORY CHECKOUT PROCEDURES WILL COMPLY WITH THIS REQUIREMENT.
OUR TRAINED FIELD PERSONNEL CAN CORRECT THE DIFFERENCE IN S/N002.
THE LIGHT SOURCE CONTAINED IN THE TABLE IS A SIGNIFICANT ADVANCEMENT
Approved For Release 2005/06/23 : CIA-RDP78605171A000400030115-3
IN THE STATE-OF-THE-ART. THE REQUIREMENT TO EXCEED 31000 FT.
A)BJECTIONAB AMBERTS, MEET .THE DIMMING RA-TiOoF. 2o:1-9 -AND 'PROVIDE .1110,IBLE
AtanceRglofifileo01%0Tili,?i,ttgp O0O
oolsT?
f 03011573 ?
'-rA^. A E FFS.
EXCEEDED ALL THESE, REQUIREMENTS SIGNIFICANTLY. TABLE
BRIGHTNESS HAS AN APPROXIMATE'OPERATING RANGE FROM 100 FT. .
LAMBERTS TO 3,500 FT. LAMBERTS AND FACTORY ADJUSTMENTS ALLOW'
THE GOVERNMENT TO TAKE FULL ADVANTAGE OF THIS INCREASED PERFORMANCE.
AS A RESULT OF THIS INCREASED BRIGHTNESS) THE REQUIREMENT OF
THE SECOND PART OF PARAGRAPH 3.1.1.1. MIGHT BE EXCEEDED BY
A SMALL PERCENTAGE POINT.FOR A SMALL PERCENTAGE OF THE TABLES.
CONSIDERS THIS TO BE OF LITTLE CONSEQUENCE AND THEREFORE
IS SETTING CONTROLS FOR BRIGHTER OPERATION.. IF THE GOVERNMENT
us
3
ESIRES)
COULD FACTORY-SET THE TABLES TO OPERATE IN.
20Q TO 3,000 FT. LAMBERTS RANGE SUCH THAT ILLUMINATION- WOULD.:
. s
FALL WITHIN THE VARIATION REQUIREMENT. 10. RECOGNIZES
THE LOW RETAINING FORCE OF S/N001. pro) LOCKS AND RESULTING OPERATOR.
INCONVENIENCE. AN IN-LINE CORRECTION HAS SEEN MADE EFFECTIVE
WITH S/N002 AND WE WILL FORWARD kCORRiCTED MOUNT IMM'iDIATELY.
FOR FIELD INSTALLATION IN S/N001. 11. (A) THE:TRACK ON THE
LEFT SIDE WAS DESIGNED TO FLOAT AT ONE END TO PROVIDE EASE
OF BRIDGE MOTION. 11. (B) THE PLASTIC PROTECTOR COVERS ON THE
Y CHAIN DRIVES WERE DESIGNED TO HAVE ADEQUATE CLEARANCE SUCH
THAT THERE WOULD BE NO DRAG ON THE SYSTEM. HOWEVER, APPARENTLY
SOME MOTION OR DISTORTION TAKES PLACE DURING SHIPMENT WHICH' ?
AUSES A SLIGHT INTERFERENCE. HAS TAKEN CORRECTIVE ACTION
TO INCREASE THE CLEARANCE AS AN IN-LINE CHANGE FOR FUTURE SHIPMENTS.
FOR DELIVERED UNITS) SLIGHT ADJUSTMENTS BY OUR FIELD REPRESENTATIVE
WILL CORRECT THIS MISALIGNMENT. 11. (C) HAS REVIEWED
-
THE DESIGN AND FEELS THAT THE POWER .CORD REEL IS ADEQUATELY
ATTACHED TO THE TABLE,. THE DESCRIPTION GIVEN IN PARAGRAPH 11. (0)
REQUIRES CLARIFICATION 'BEFORE WE CAN MAKE FURTHER COMMENT.
11. (D) THE TILT MECHANISM WHICH CONTAINS THE MERCURY SWITCH
fIS THOROUGHLY 4EpSroTvEeDdIF'0IrNIZTAaLsL D AND ADjjj$Tijii.ziop_ to_ stu_au. 1-2.L12:
THIS DEFECT APPEARS UNIQUE TO S/N001) AND WILL BE CORRECTED
le eE2005/06/23 ? CIA-RDP7oB05171AUOU4WUJUi Tot3
STA
,STA
Td_Opti.F1LLDREpRESENTATIVE.' SUBMITS'THAT-THIS:DESIGU.,
Mr.OdligliBIFTAIO%
215ffillglikCINFRIMIWriTERII,J3
, ? . - , ?
-
BEFORE WE CAN COMMENT FURTHER. GENERALLY WE ARE -KEENLY.AWARE--
OF THE IMPORTANCE OF QUALITY CONTROL, AND ARE IN A CONTINUAL
REVIEW PROCESS TO ASSURE THAT STANDARDS ARE ACCEPTABLE AND
TOTALLY IMPLEMENTED. WE WILL CONTINUE TO BE ALERT TO THESE
FACTORS AND INCORPORATE IMPROVEMENTS AS REQUIRED. 12. INASMUCH
AS THE ONLY METHOD OF MEASURING THIS PARAMETER IS IN THE SOLE
POSSESSION OF OUR GOVERNMENT CUSTOMER,
REQUESTS DETAILED STAT.
INFORMATION AS TO,HOW THE MEASUREMENTS WERE TAKEN AND, IN PARTICULAR,
THE REASONS FOR THE VARIATIONS FROM TEST 1 TO TEST 2. WITH.:
THIS KNOWLEDGE FOR THE FIRST TIME, WE WILL REVIEW WITH OUR
SUPPLIER AND TAKE: THE NECESSARY CORRECTI1)E-ACTION'ON 'FUTURE,
NITS. HAS INCLUDED THESE SPECIFICATIONS TO OUR LAMP:
SUPPLIER, AND HAVE. BEEN WORKING WITH.HIMHFOR A.LENGTHY"PERIOD
IN AN ATTEMPT TO CLARIFY AND COMPLY WITH THESE DIFFICULT
PARAMETERS ATTACHMENT 2(MAIN HEADING). ITEM 1 THROUGH 3 5 THROUGH g ,
10 12 13 AND 14 HAVE BEEN CORRECTED.. BY OUR FIELD .REPRESENTATIVE ITEM 4.
THE FIRST 6 UNITS HAVE BEEN COLLIMATED AND BALANCE OF UNITS WILL BE
2 ,
ACCOMPLISHED SHORTLY ITEM 9 JERKY FILM MOTION APPEARS-TO E SUBJECTIVE
IN NATURE OR OCCURING UNDER SPECIAL CONDITIONS. WHEN MORE
DEFINITIVE INFORMATION IS AVAILABLE ME CAN MAKE EXPLICIT-COMMENT.
ITEM 11, WILL REPLACE GLASS AS REQUIRED. ITEM 15, THIS
/S A SUBJECTIVE MATTER; PERHAPS A LIGHT SMOOTHING PROCEDURE
WITH FINE STEEL WOOL OR CROCUS CLOTH BY OUR FIELD REPRESENTATIVE
MIGHT BE APPROPRIATE CONFIRMING LETTER TO FOLLOW
9.32A EST JAN 3-- 1971
Approved For Release 2005/06/23 : CIA-RDP78605171A000400030115-3
Approved For Release 2005/06/23 : ,C.IA-RDP78B05171A000400030115-3
List of Contractual Defects on Table Ser. No. 001
Defects
1. The table tilts by lifting the back of the unit and hinging
on the front. This creates a nutcracker effect at the hinge.
The tilt switch is located very close to the hinge, and it has ,
been determined that an operator could very easily suffer crushed
:fingers :while operating the switch..
2. The Y motion is locked when the table is tilted. This systeM
is actuated by a mercury 'switch. The adjustment required to pro-L
vide this locking feature just after tilting starts, and to
release the lock after it becomes horizontal, is quite touchy. ,
The prototype table is just as likely to be locked in the horizon-
tal position as unlocked. If this is relieved, the carriage may
start to roll forward when tilting occurs before locking takes-
place.
3. Using a gauge configured to show the maximum overall width of
a 6.6" film reel, it was found that interferences exist at all.
reel stations. Further checks; on the production models available
at that time showed that 23 of 24 stations checked are too narroW
and will not accept the 6.822 inch dimension specified.
.The cable which connects the focus mechanism to the power
supply and electronics at the back of the table prevents the
focus mechanism from realizing full travel to the back of the
viewing surface.
5. Markers are provided on the table to aid in placing the motors
and idlers for various film configurations. The motors have i
matching markers on one side. However, the motors must be used in,
such a way that the side not containing the marker is in view.
Consequently, markers must be placed on both sides.
6. The MLT is made in two parts, an elevating stand and the light
table proper. If the light table is not put on the stand at the
right place, or if it shifts while being transported, the lower
Para. 3.6.5
fans, drive
enclosed to
operator.
Attachment 1
Contract References
(4) - Moving parts such as.venti
belts, or gearS, shall be shielde(:).
prevent inadvertent access by:the
Para. - A ma ridge furnished wit
tilting stand shall be proVided with an oTtior:?
fail-safe override to prevent uncontrolled
in the Y direction when the table is tilted,
move the carriage in the Y direction with the
horizontal; it shall be neCessary only to rele
the Y friction.lock. In a tilted -positnr,
safe interlock shall be activated prevetting
translation unless the interlock is purposely
defeated.
Para. 2 - The table shall accommodate spools
ranging up to and includirg the size of spool
. specified in Military Standard M326565-22 cr
to capacity with filth,
Para. 3.4.1.2 - With any of the microstereoscop
fixed in the mount, and using the ...enter of th
Scope as a reference; translation in the 7. din:
shall be adequate to' cover the full 75" deT.th
the glass viewing surface.,
Para. 3.3.1.2 - A visual reference scale and
ing device with positive detents shall be proy
to allow accurate poSitioning of the brackets
hold the various width ,spools and assure accur-
tracking across the glass viewing surfaces of -
film parallel to the longitudinal axis of the '
table and to each other.
Para. 2' - Provision s.iall be made for viewing_
in-line viewing of two of the same widths, of -
5", 6.6" or 9.5" wide film.
Approved For Release 2005/06/23 : CIA-RDP78605171A000400030115-3
vIA
Approved For Release 2005/06/23 : CIA-RDP78605171A000400030115-3
cover is prevented from dropping by the tilt and elevating .
switch housing. The lower cover will not open when the table
is tilted.
7. The mechanism which takes up the dead loop at the center of
the table employs cable guides which hold the actuating
mechanism in its track. These cable guides have profiles whiCh
prevent the looping mechanism -.Cram reversing direction at one
point in its travel.
8. The lower cover latches are. very difficult to operate, due ?
to their placement and design. .
9. The illumination sources are not equal within 100 fiat
maximum. The left measured 3225 fL max and the right 3010 fL max.
The change in output of one side when the othar is turned
completely down or up should not exceed 100 fL, This change was
measured to be 150 fL on the left side and 165 fL on the right
side.
10. The screws holding, the pod in the optics mount do not
provide adequate force to prevent unwanted motion
11. There have been instances of evidence of poor quality con-
trol. a) The bearing track on the left side was not fastened
tightly. b) The plastic protector covers on the Y chain drives
dragged the chain and drive elements. c) The power cord reel
fell off of the unit. d) The tilt lock mercury switch was not
set properly.
?
Approved For-Release 2005106/23 : CIA-RDP781305
Para. 2 - The table shall include a simple film
looping mechanism which shall allow formin7, a
of film below the-t-abIe-n order that separat
frames, on the same roll of film, may be arran
adjacent to each other for convenient stereo
Looping of parallel rolls of fiTm
-recuired. This mechanism shall be capab7e (-(F'
forming a continuous film loop from 0 to 76 All
Para 3.2.1.4 - All control's., including the film
hand wheels (on the manual version), shall be
positioned so they can be easily manipulated. -
this respect, it is understood that the locatl.:'
of the controls, as supplied on the prerioduci
model (when accepted), will be Satisfactory.
Para. 3.1.1.1 - The maximum levels of the two
illumination sources shall not differ by more
100 foot lamberts at the time of this meas=Em_..
With one of the two sources set at max-mum cr
minimum illumination level, there ,shall not be
change of more than 100 foot lam-serts in
tion level of that source when the ill ir'tic:n
level of the other source is adjusted threugr,_Allk
its full range.
Para 3.5.1 - Nounting devices shall he suffic
rigid to preclude instrument misalignment and L.
of collimation of the optics with res-cect to t: _
viewing surface during normal handling and
operation.
Contract. Page 3, ACCEPTANCE - Final inspectiOn
and acceptance of artcles shall be by demons:::'
of successful performance and completion of to;..
set forth in a mutually approved Acceptance Ic
Plan (ATP), which shall be 'provided for
J494.
wor to commencement of
'Ineeaoi units of any item.
Para. 11 (continued)
Approved For Release 2005/06/23 : CIA-RDP78B05171A000400030115-3
Contract, Page 4, WARRANTY OF ST,3117'77ES? - _277
supplies furnished under this Contract ll
be free from defects in mate-Y-72.1 or wn-r?n,lansh
maw= conform with the specifications and a
other requirements of this Contract.
12. The color rendering index (CRT), correlated color temperature Para. 3.1.1.2
(CCT), and chromaticity an points (X, Y) were measured for each
side and are listed below.
Left Side Right Side
Test 1
Test 2
CCT
55714
5689
CRI
57.69
55.28
Y_
0.3304
0.3278
Y
0.3626
0.3616
Test 1
Test 2
5565
5706
57.53
55.93
0.3311
0.3275
0.3659
0.3614
CCT
5000+500K
CRI
270
X
0.345
Y
0.358
3
Approved For Release 2005/06/23 : CIA-RDP78B05171A000400030115-3
a
Approved For lease 2005/06/23 : CIA-RDP78B0517.00400030115-3
A
10 10 01 M JAN
to-031(
//
.CJ AX00C IT.A391) NL PDE TDI: 'FAN LOS ANGELES CALIF JAN 7
7-7
NE STERN UNION'ATTN TELEPHONE 524-6654
"1
rvv,
UILL CALL 3109 WILSON.DLVI'' ARLINGTON VTR
SUBJECT: REFERENCE CUSTOMER LETTER OF 4 JANUARY
1971 ON LI GET TABLE DEFECTS, 1. WE SUBMIT THAT NO SAFETY HAZARD
EXISTS, OTHERWISE WE. WOULD HAVE ALTERED TABLE, DESIGN. THIS
FIRST UNIT WAS THOROUGHLY EXAMINED BY YOUR PERSONNET. IN LOS
ANGELES. IF YOU ELECT, WILL ACCEPT -A .SCOPE CHANGE TO
CORRECT THE SITUATION, 2, THIS FAULT APPEARS TO BE UNIQUE TO
ABLE S/N001, AND DOES NOT APPEAR ON THE ATTACHMENT NO, 2 REGARDING
THE INSPECTION OF 14 PRODUCTION TABLES. OUR 'FIELD SERVICE-REPRESENTATIV7
WILL INSPECT AND CORRECT THIS DEFICIENCY ON S/N001.- 3. M526565
DOES SNOT COVER THE DIMENSIONS OF A 6.6" REEL,. TOOK THE
POSITION THAT 6.61;FILU WIDTH
BE FOR
THE 5" FILM WIDTH IN SAID STANDARD AND EXTROPOLATED APPROPRIATE
DIMENSIONS PEON THE 5" SPECIFICATION. THIS RESULTED IN A DESIGN
WHERE THE MAXnUM-TOLFRANCED REEL WOULD BE NO GREATER THAN
S.782-INCHES. THE PROTOTYPE PREVIOUSLY DELIVERED AND EVALUATED
DY YOU AND UNIT SERIAL 001 INSPECTED HERE IN LOS ANGELES. BOTH
INCORPORATE THIS DESIGN. UNDERSTANDS THAT CURRENT 6...6"
REELS AVAILABLE TO THE CUSTOMER EXCEED THIS NUMBER AND THE
CRITICAL NATURE OF THIS PARAMETER. WE WILL IMMEDIATELY INSTITUTE
CORRECTION WHICH IS FIELD RETROFITTABLE AND FACTORY IMPLEMENTED,
AND WILL SUBMIT. A CLAIM COVERING THIS '-:COPE CHANGE.
SUEMITS.TNAT THE TABLE
COMPLETELY MEETS THE REQUIREMETS OF
PARAGRAPH 3.4.1.2, AND THAT:THE CABLE CAN BE EASILY MOVED ASIDE
r1iTh A 1==-nUTTT77?PRACT.?
77c.
CODING OH '10.1uR,:J IS MEANT ONLY AS A VISUAL REFERENCE GUIDE
77,E Alsip THE PRECISE POSITIONING IS OBTAINED BY MECHANICAL DETENTING
ri m ,
IN WHICH AN OPERATOR CAN FEEL LOCK-IN. WHEN MOTORS ARE USED
rJa
(79
IN THE SPLIT VERTICAL MODE, THIS VISUAL REFERENCE CAN BE OBTAINED
BY USING. THE LEFT REAR MOTOR ON THE LOWER RICHT POSITION AND
THE RIGHT REAR MOTOR ON THE LOWER LEFT POSITION, MOTORS ARE
EASILY INTERCHANGED BY SIMPLE PLUG-IN OPERATION..
THAT DESIGN MEETS THE REQUIREMENTS OF 3.3..1.2 6.
SUBMITS
RECOGNIZES
THE CONDITION OF LOWER COVER BEING PREVENTED FROM OPENING WHEN -
THE TABLE HAS SHIFTED IN ITS HORIZONTAL POSITION RELATIVE TO
THE ELEVATING STAND. WE WILL MAKE AN IN-LINE CORRECTION TO
PREVENT THE TABLES FROM SHIFTING; AND. PROVIDE FIELD-INSTALLED
PLUGS TO HOLD THE ? TABLES IN THE CORRECT POSITION, OPERATIONAL
iPROCEDURES WILL REQUIRE THAT THE TABLE DE LOWERED TO THE HORIZONTAL
POSITION FOR LOADING THE IN-LINE VIEWING OF TWO SIMILAR-WIDTH
L-n
" FILMS, AND THIS IS A sLmPLE OPERATION. 7. RECOGNIZES
iA DESIGN TRADE-OFF FOR SAFETY AND CONVE IENCE OF THE OPERATOR
IIN THE KNEEW)LL AREA, SUBMITS THAT THE OPERATION IS
JA SIMPLE ONE IS NOT AN OPERATING caTTNI, AND IT NUTS THE?
REQUIREMENTS 07 PARAGRAPH 3.2.1.4. 9. PROVISION HAS BEEN MADE
FOR ADJUSTNENT BY FACTORY TRAINED PERSONNEL TO BALANCE THE .
TWO ILLUMINATION SOURCES IN ORDER TO MEET THE REQUIREMENTS
THE INCONVENIENCE OF THE 'TAKE-UP LOOK BEING BLOCKED IN ONE
DIRECTION DUE TO THE CABLE GUIDES, AND WILL. MAKE AN IN-LINE
CHANGE. TO CORRECT THIS AND PROVIDE A BASIS FOR FIELD RETROFIT
5'. THE LOCATION OF THE LOWER COVER LATCHES ARE THF RESULT 07
OF THE FIRST PORTION OFPARAGRAPH 3.1.1.1.
WILL ENSURE
THAT FACTORY CHECKOUT PROCEDURES WILL COMPLY WITH THIS REQUIREMENT.
OUR TRAINED FIELD PERSONNEL CAN CORRECT THE DIFFERENCE IN S/N002,
THE LIGHT SOURCE CONTAINED IN THE TABLE IS A SIGNIFICANT ADVANCEMENT
IN THE STATE-OF-TEE-ART REQUIREMENT R7CUIREM7NT TO EXCEED 41000 FT.
LAMBERTS, MEET THE DIMMING RATIO OF 20I, AND PROVIDE NO VISIT:31,F
OBJECTIONABLE-FLICKER. RESULTED TN DUEICUT.T DFSTC.N TP=-07vS,
Approved Fogilease 2005/06/23 : CIA-RDP76130517.000400030115-3
EXCF:EDED ALL THESIgnEo.WIREN7:::NTS ST_ CN.TFICANTL\:. TA:31-7.
rTh
il;RIGHTNESS HAS AN APPROXIMATE OPERATING RANGE FROM 100 FT.
Approved For Release 2005/06/23 : CIA-RDP78605171A000400030115-3
LAMBERTS TO 3,500 FT . LAMBERTS AND FACTORY ADJUSTMENTS ALLOW
THE GOVRNMENT TO TAKE FULL ADVANTAGE OF THIS INCREASED PERFORMANCE
AS A RESULT OF THIS INCREASED BRIGHTNESS, THE REQUIREMENT OF
THE SECOND PART OF PARAGRAPH 3.1.1.10 MIGHT BE EXCEEDED 13y
A SMALL PERCENTAGE POINT FOR A SMALL PERCENTAGE OF THE TABLES.
CONSIDERS THIS TO BE OF LITTLE CONSEQUENCE. AND THEREFORE
IS SETTING CONTROLS FOR BRIGHTER OPERATION. IF THE GOVERNMENT
'F '),E DESIRES, COULD FACTORY-SET THE TABLFS TO OP7RATE IN.
,... ,.
-r-.
200 'TO 3,000 FT. LAMBERTS RANGE SUCH THAT ILLUMINATION WOULD
PIE
,04
171171 FALL WITHIN. THE VARIATION REQUIREMENT. 10a RECOGNI7ES
toJ ?
1--AD
' Ta LOU RETAINING FORCE OF S/N001 PAD LOCKS AND RESULTING OPERATOR
. .
FOR miLD INSTALLATION IN S/N001. 1.1. (A) THE TRACK ON THE ?
LEFT SIDE WAS DESIGNED TO FLOAT AT ONE END TO PROVIDE EASE
OF BRIDGE MOTION. 11. (B) THE PLASTIC PROTECTOR COVERS ON THE
C7
c_ ?
Y CHAIN DRIVES WERE DESIGNED TO HAVE ADEQUATE CLEARANCE SUCH
THAT THERE WOULD 11-: NO DRAG ON THE SYSTEM. HOWEVER, APPARENTLY
SOME MOTION OR DISTORTION TAKES PLACE DURING SHIPMENT;WHICH
CAUSES A SLIGHT INTERFERENCE. HAS TAKEN CORRECTIVE ACTION
N
ICONVENIENCE. AN IN-LINE CORRECTION HAS BEEN MADE EFFECTIVE
WITH S/N002. AND WE WILL FORWARD A CORRECTED'MOUNT IMMEDIATELY
TO INCREASE THE CLEARANCE AS AN IN-LINE CHANGE FOR FUTURE SHIPMENTS.
FOR DELIVERED UNITS, SLIGHT ADJUSTMENTS BY OUR FIELD REPRESENTATIVE
?
WILL CORRECT THIS MISALIGNMENT. 11. (C) HAS REVIEWED
THE DESIGN AND FEELS THAT THE POWER CORD REEL IS ADEQUATELY
ATTACHED TO THE TABLE. THE GIVEN IN PARAGRAPH 11. (0)
REQUIRES CLARIFICATION BEFORE WE CAN MAKE FURTHER COMMENT.
110 (D) THE TILT MECHANISM WHICH CONTAINS THE MERCURY SWITCH
,IS THOROUGHLY TESTED, INSTALLED AND ADJUSTED PRIOR TO SHIPMENT.
THIS DEFECT APPEARS. UNIQUE TO S/N001, AND WILL BE CORRECTED
BEFORE l'!7 CAN COMMENT FURTHER. GENERALLY WE ARE KEENLY AWARE
?
?Y% ,OF THE IMPORTANC7 OF QUALITY CONTROL, AND ARE IN A CONTINUAL
4
REVIEU pp.oGESS TO ASSURE THAT STANDARDS ARE ACCEPTABLE AND
'TOTALLY IMPLEMENTED. VE WILL CONTINUE TO BE ALERT TO THT;'SE
.01JR ISUVTIS :AT 1:,1L) DEIGN
SATISFIES REQUIREMENT. ALSO, ADDITIONAL INFORMATION IS REQUIRED
---'-'cl\CTORS AND INCORPORATE IMPROVEMENTS AS REQUIRED. 12a INASMUCH
?
AS THE ONLY METHOD OF MEASURING THIS PARAMETER IS IN THE SOLE
?T.i POSSESSION OF OUR GOVERNMENT CUSTOMER, EQUESTS DETAILED
INFORMATION, AS TO HOW THE MEASUREMENTS WERE TAKEN AND, IN PARTICULAR,
THE, REASONS FOR THE VARIATIONS FROM TEST 1 TO TEST 2. WITH
THIS KNOWLEDGE FOR THE FIRST TIME, WE WILL REVIEW ?WITH OUR
SUPPLIER AND TAKE. THE NECESSARY CORRECTIVE-ACTION ON FUTURE
.UNITS. HAS INCLUDED THESE SPECIFICATIONS TO OUR LAMP
SUPPLIER, AND HAVE BEEN WORKING WITH HIM FOR A LENGTHY 'PERIOD
IN AN ATTEMPT. TO CLARIFY AND COMPLY WITH THESE DIFFICULT
PAPAMETERS ATTACHMENT 2 (MAIN HEADING). ITEM 1 THROUGH 3 5 THROUGH g
10 12 13 AND 14 HAVE BEEN CORRECTED BY OUR FIELD R7PRESENTATIVE ITEM A
THE FIRST 6 UNITS HAVE BEEN COLLIMATED. AND BALANCE OF UNITS WILL BE
ACCOMPLISHED SHORTLY ITEM 9 JERKY FILM NOTION APPEARS TO BE SUBJECTIVE
IN NATURE OR OCCURING UNDER SPECIAL CONDITIONS. WHEN MORE
DEFINITIVE INFORMATION IS AVAILABLE WE CAN MAKE EXPLICIT COMMENT.
ITEM 11, WILL REPLACE GLASS AS REQUIRED. ITEM 15, THIS -
US A SUBJECTIVE MATTER; PERHAPS A LI GUT SMOOTHING PROCEDURE
WITH FINE STEEL WOOL OR CROCUS CLOTH BY OUR FIELD REPRESENTATIVE
MIGHT BE APPROPRIATE CONFIRMING LETTER TO FOLLOW
.932A EST JAN g 1971
Approved Fo
ease 2005/06/23 : CIA-RDP7860517 00400030115-3
_
Approved For Release 2005/06/23 : CIA-RDP78B05171A000400030115-3
List of Contractual Defects on Table Ser. No. 001
Defects
1. The table tilts by lifting, the back of the unit and hinging
on the front. This creates a nutcracker effect at the hinge.
The tilt switch is located very close to the hinge, and it has !
been determined that an operator could very easily suffer crushed ;
fingers while operating the switch.
2. The Y motion is locked when the table is tilted. This system
is actuated by a mercury switch. The adjustment required to pro
vide this locking feature just after tilting starts, and to
release the loch after it becomes horizontal, is quite touchy.
The prototype table is .just as likely to be locked in the horizon-
tal. position as unlocked. If this is relieved, the carriage may !
start to roll forward when tilting occurs before locking takes
place,
3. Using a gauge configured to show the maximum overall width of
a 6.6" film reel, it was found, that interferences exist at all.
reel stations. Further checks on the production models available
at that time showed that '23 of 214 stations checked are too narroW
and will not accept the 6.822 inch dimension specified.
40 The cable which connects the focus mechanism to the power
supply and electronics at the back of the table prevents the
focus mechanism from realizing full travel to the back of the
viewing surface.
5. Markers are provided on the table to aid in placing the motors
and idlers for various film configurations. The motors have
'matching markers on one side. :However, the motors must be used in:
such a way that the side not containing the marker is in view.
Consequently, markers must be placed on both sides.
6. The'liIT is made in two parts, an elevating stand and the light
table proper. If the light table is not put on the stand at the
right place, or if it shifts while being transported, the lower
Attachment I
n1 r
Contract References
Para. 3.6.5 (4) - Moving parts such as ventilatinr:
fans, drive belts, or gear, shall be shielded or
enclosed to prevent inadvertent access by the
operator,
Para. - A manual oriage furnished with i
tilting stand shall be proVided with an optional
fail-safe override to prevent uncontrolled MetiOn T
in the I direction when the table is tilted. To
move the carriage in the Y direction with the tah:
horizontal, it shall be neCessary only to rel
the I friction lock. In a. tilted Position, a laJ,
safe interlock shall be activated preventing Y
translation unless the interlock is purPosely
defeated.
Para. 2 - The table shall accommodate spools .
ranging up to and including the Size of spool
specified in Military Standard MS26565-22 loaded
to Capacity with filM.
Para. 3.4.1.2 - With any of the microstereoscoren
fixed in the mount, and using the .center of the
Scope as a reference; translation in the Y direo-6_
shall be adequate to cover the full 15" depth of
the glass viewing surface.1
Para. 3.3.1.2 - A visual reference scale and indi:,Y
ing device, with positive de-tents shall be providar
to allow accurate poSitioning of the brackets to
hold the various width spools and assure accurate
tracking across the glass viewing surfaces of the
film parallel to: the longitudinal axis of the lic.1!
table and to each other.
Para. 2 - Provision shall be Made for viewing...
in-line viewing of two of the same widths, of 702!.
5", 6.6", or 9.5" wide ? film.
Approved For Release 2005/06/23 : CIA-RDP78605171A000400030115-3
Approved
or Release 2005/06/23 : CIA-RDP78605171A000400030115-3
cover is prevented from dropping by the tilt and elevating ,
switch housing. The lower cover will not open when the table
is tilted.
7. The_mechanism which takes up the dead loop at the center of
the table employs cable guides which hold the, actuating
mechanism in its track. These cable guides have profiles whiCh
prevent the looping mechanism from reversing direction at One ?
point in its travel.
8. The lower cover latches are very difficult to operate,- due
to their placement and design. .
9. The illumination sources are not equal within 100 fL at
maximum. The left measured 3225 fL max and the right 3010 fL max.
The change in output of one side when the other .is turned
completely down or up should not eXceed 100 fL. This change was
measured to be 150 fL on the left side and 165 fL on the right
side.
10. The screws holding the pod in the optics mount do not
provide adequate force to prevent unwanted motion.
11. There have been instances of evidence of poor quality con-
trol. a) The bearing track on the left side was not fastened
tightly. b) The plastic protector covers on the Y chain drives
dragged the chain and drive elements. c) The power cord reel
fell off of the.unit. d) The tilt lock mercury switch was not
set properly.
Approved For Ielease 2005/06/23 : CIA-
Para. 2 - The table shall include a simple film
looping mechanism which shall allow forming a locT
of film below the:table-in order that separated
frames, on the same roll of film, may be arranged.
adjacent to each other for convenient stereo
viewing. Looping of parallel rolls of film is not
required. This mechanism shall be capable of.
forming a continuous filth loop from 0 to 76 inik
Para 3.2.1.4 - A11 control's, including the film
hand wheels (on the manual version), shall be
positioned so they can be easily manipulated. Tn.
this respect, it is understood that the location
of the controls; as supplied on the preproduction
model (when accepted),, will be Satisfactory.
Para. 3.1.1.1 - The maximum levels of the two
illumination sources shall not differ by more th:n
100 foot lambertsat'the time of this measurement,
With. one of the two sources set at,. maximum or
minimum illumination' level, there ,shall not be a
'change of more than 100 foot lamberts in
tion level of that. source when the' illumination
level of the other source is adjusted througholl
its full range.
Para 3.5.1 - Mounting devices shall be sufficin-
rigid to preclude instrument misalignment and
of collimation of the optics with respect to the
viewing Surface during normal hand7ing and
operation.
Contract, Page 3, ACCEPTANCE - Final inspectiOn
and acceptance of articles shall be by demonstrati
of successful performance and completion of tet
set forth in a mutually approved Acceptance Test
Plan. (ATP), which shall be Provided for approval
two (2) weeks prior to. Commencement of tests or?
FUDPME0471,4000404020345Aits of any item.
Para. 11 (continued)
Approved For Release 2005/06/23 : CIA-RDP78B051714000400030115-3
Contract, Page 4, 'WARRANTY OF SUPPLIES - All
supplies furnished under this Contract .will
be free from defects in material or workmanship
and will conform with the specifications and all
other requirements of this Contract.
12. The color rendering index. (CRT), correlated color temperature Para. 3.1.1.2
(CCT), and chromaticity aim points (X, Y) were measured foF each
side and are listed below.
,Left Side Right Side
Test 1
Test 2
Test 1
CCT
5574
5689
.
5565
CRI
57.69
55.28
57.53
X
0.3304
0.3278
'
0.3311
Y
0.3626
0.3616
0.3659
Test 2
5706
55.93
0.3275
0.3614
CCT
5000+500K
CRI
270
X
0.345 .
Y
0.358
- 3 -
Approved For Release 2005/06/23 : CIA-RDP78b05171A000400030115-3
4