(Sanitized)PRINT PROCESSOR(Sanitized) DIGEST OF INSTALLATION SPECIFICATIONS

• Document Type: CREST
• Collection: NGA Records (Formerly NIMA)
• Document Number (FOIA) /ESDN (CREST): CIA-RDP78B04747A003000060008-5
• Release Decision: RIPPUB
• Original Classification: K
• Document Page Count: 3
• Document Creation Date: December 28, 2016
• Document Release Date: November 16, 2001
• Sequence Number: 8
• Content Type: REQ

Approved For Release 2002/01/02 : CIA-RDP78B04747A003000060008-5
PRINT PROCESSOR
DIGEST OF INSTALLATION SPECIFICATIONS
1. Machine Placement
a.
INI
representative will be on hand to supervise
p acement of then the area you designate.
The machine. mus e evel in its operating area.
b. Machine dimensions are:
Width - 3711
Length - 9811
*Height - 8411
Approx. Weight - 1500 lb.
*Note: Shipping height will be reduced to 78".
c. Operating area should have following clearances:
Minimum of 18" on the ends
Minimum of 18" on the back side
Minimum of 36" on the front or operating side
2. Services
a. Electrical requirements: 208 volt, 3-phase, 60-cycle,
4-wire, protected for 40 amperes. Overload protection
and disconnect.
b. Air: 120 PSIG. 40 CFM Free discharge. Oil free.
Note: We have found Quincy Compressor Company,
Quincy, Illinois, Model F325, 5 H.P. Motor,
80 gal. storage, 3-phase, 220-440 V, 60-cycle
to be adequate.
c. Water: Hot - 160?F - 6 gallons per minute. Flow with
minimum recovery of 1 gallon per minute.
Cold - 6 gallons per minute.
Declass Review by NIMA / DoD
Approved For Release 2002/01/02 : CIA-RDP78B04747A003000060008-5
STATINTL
STATINTL
STATINTL
STATINTL
 Approved For Release 2002/01/02 : CIA-RDP78B04747A003000060008-5
- 2 -
d. Drain: Floor drain with not less than 1-1/4" line.
3. Atmospheric Controls - Room temperature must be maintained at
a level not below 65?F and not in excess of 80?F.
4. Illumination processing room must have
appropriate safelighting. We recommend series OC Safelight
Filter. Four 25-watt lamps with filters and properly placed
should be sufficient.
PAS/jh
6/21/63
STATINTL
Approved For Release 2002/01/02 : CIA-RDP78B04747A003000060008-5
 Approved For Release 2002/01/02 : CIA-RDP78BO4747AO03000060008-5
During the period that the original Processors were
introduced for field testing up untl. - e presen time, a number
of_chan es have been made in the basic unit. At the request of
0 I am listing the most recent improvements which are
now .on p esent models but were not on models tested six months
ago.
1. Lens sled has been motorized.
2. Finger stock has been redesigned and now
operates by solenoid and an electric
footswitch.
3. Hydraulic pump motor has been changed from
1/4 H.P. to 1/3 H.P. and the motor and
pump assembly moved to opposite side for
easier servicing.
4.' A vertical water knife operated by hydraulic
cylinder and cam was incorporated to increase
operator's visibility when loading and unloading
paper.
5.' Linkage.pin to the turntable solenoid has been
enlarged and material specs changed to SAE 4140 steel.
6. Wash shield has been modified to remove the interference
at 1:1 enlargement.'
7. Handles.on the negative masking adjustment have been
knurled.
Approved For Release 2002/01/02 : CIA-RDP78BO4747AO03000060008-5