MINUTES OF MEETING 15 FEB. 1966

• Document Type: CREST
• Collection: NGA Records (Formerly NIMA)
• Document Number (FOIA) /ESDN (CREST): CIA-RDP78B04770A001600020014-9
• Release Decision: RIPPUB
• Original Classification: K
• Document Page Count: 6
• Document Creation Date: December 28, 2016
• Document Release Date: June 6, 2005
• Sequence Number: 14
• Publication Date: February 23, 1966
• Content Type: MEMO

roved Fo lease 2005/06/23: CIA-RDP78BO477~p01600020014-9
INT -OFFICE MEMORANDUM
25X1
Meeting Held at
DATE 23 February 191
LOCATION
SUBJECT Minutes of Meeting 15 Feb.1966DRGANIZATION
25X1
25X1
The purpose of the meeting was to discuss the results of the
F.E.D. tests, machine controls and operation and schedule.
The problems presented by the monitors as a result of the
F.E.D. tests were as follows:
1. Intermittant problem stopping on two frames of 70 mm film.
What about 5" frames on 5" wide film with one inch frame'
separation.
. Great difficulty stopping on 1/8" boundaries.
3. Poor tracking of transport, particularly with respect to
the edge sensor.
Constant transport' speed problem.
5. What is necessity for dancer roller.
6. What are transport speeds. Can they be varied to accom-
modate narrow boundaries. .
7. What is minimum space between frames that can be sensed.
8. What adjustments by operator are necessary.
9. What is delivery schedule.
CEA "A"
NGA Review
Complete Approved For Release 2005/06/23: CIA-RDP78BO477OA001600020014-9
 Approved For lease 20.p5/06/23; CIA-RDP78B0477&01600020.014-9
-many variables, such as uniformity of boundaries, density,
The minimum space that can be sensed is a function of,.
advances, film is always advanced 1/3 speed.
down for-the last 5" of advance. With shorter than 12"
etc. It may be possible to sense 1/8" boundaries under
.certain conditions if a proportionately.high percentage of:
;frame, the transport be stopped and .a failure' indication
'..The customer requested that, in the event,of a skipped
raise triggers can be tolerated:
'be provided on the control panel.
25
.3 position switch: (1) loci.' density :boundaries;` (2).
high density boundaries low ranger,> ; (3)N'high.'density
boundaries high range.
'4 position Mode Switch:
Fixed density reference
Equality
. Combination of (1) and (2)
Edge reference
Reference Density control' associated.;with.-mode`
'Frame Length Timer Control
.:Boundary Timer Control
Skipped frame reset pushbutton
These are described elsewhere in a summary
by on 14 February. 1966..
The --meeting was continued at.; the shop where;
the Printer and Pre' View.and Punch Station . were' shown to he
technical monitors
 Approved For?lease 2005/06/23 : CIA-RDP78B0477701600620014-9
chassis ,above and behind the raw stock supply spool.
The F.E.D. controls would be located on the F.E.D.
will further permit use of a standard white light for
would light-seal the upper raw-stock
pull out drawer in accordance with the Design Plan. .This.'1
,.viewing rather'than asafelight, if required.
The pre-view and punch station would be mounted'on legs.
pointed out that?this did not-contain much.contingency for
seated:::
An attempt.would be made to provide microscope and controls--
at a comfortable operating height when the operated is
'A schedule was presented to:-the monitors (enclosed). It was
;.component delivery and was our best estimate;, at ahe ..present' time.::
Approved For Release 2005/06/2,3 CIA-1 Dp78B04770A00I:6Q00Z0014'-
 PI L=82 P~~vr~~-/
Approved F e e a 2005/06/23 I ARDP78B04770A0016Q002001.4=9
~ J c-~ , ~_ n. G s
l e$jCN 2i2r4, r,Af c
% o c V R5,02C- t'7
,~132i C.47'/0A/
.5 U-42 3 l y
JciwT SysTG--2 7 isr
J7F12,? 6N.sT/fj7/cn/ 75ST
-.-Dom[/c~?2, . /~2~nlZ?c~'
TG S T RE,ppRT
OPE J 7- t2s u14'YDi3 00 /c
n1Q i nl TE AJ & c & /2'74 4/1) 1~
SP42cs L/&T
En16irV EE:Qj n)l 724-W ,16-s
Ni o Ai rtJ L y Lm-&ie i?~sP?'
Approved- For Release 2
fE/3
)05106/23 CIA-RO7~B047710A001600~
i9P/Tl
/Y/.o y
/0
A
f 0
.31
3!
 Approved 05/06/23: CIA-RDP78B0 A7,70A001600020014-9
25X1
25X1
b
25X1
--------------
1
F
-i, .Approve ForfReIe.e;2005/06/23 : CIA-RDP78BO477OA001600020014-9
Z-