MONTHLY STATUS REPORT CONTRACT(Sanitized)

Document Type: 
Document Number (FOIA) /ESDN (CREST): 
CIA-RDP78B04747A000900010016-5
Release Decision: 
RIPPUB
Original Classification: 
C
Document Page Count: 
8
Document Creation Date: 
December 28, 2016
Document Release Date: 
June 18, 2001
Sequence Number: 
16
Case Number: 
Publication Date: 
July 10, 1964
Content Type: 
LETTER
File: 
AttachmentSize
PDF icon CIA-RDP78B04747A000900010016-5.pdf176.26 KB
Body: 
Approved For R 04747AO00900010016-5 July 10, 1964 Ref: 6541PLI-79 Ft. Davis Stat Washington, D. C. 20020 25X-A Subje >hly Status Report Enclosed herewith you will find five (5) copies of the second monthly status report under subject contract. Very truly yours, CONTROL DIVISION Contract Administration and Federal Taxes Enclosures: As Listed Declass Review by NIMA / DoD CONFIDENTIAL Approved For Release 2001/08/13 : CIA-RDP78B04747A000900010016-5 Approved For Release 2001/08/13 : CIA-RDP78B04747A000900010016-5 Second Monthly Letter Report OPEN GATE STUDY PERIOD: 28 May - 29 June 1964 Approved For Release 2001/08/13 : CIA-RDP78B04747A000900010016-5 Approved For Release 2001/08/13 : CIA-RDP78BO4747A000900010016-5 TABLE OF CONTENT'S I, Section No. Page No. I. PURPOSE OF STUDY. . . . . . . . . . . . 1 II. ACTIVITY OF THIS REPORTING PERIOD . . . 1 A. EXPERIMENTAL PROGRAM. . . . . . . . 1 B. 'T'ECHNIQUE EVALUATION. . . . . . . . 4 III. PLANS FOR NEXT PERIOD . . . . . ... . . 5 LIST OF ILLUSTRATIONS Figure No. Page No. 1. Experimental Setup. . . 3 2. Effect of Contacting Pressure on Output Resolution . . . . . . . . . . . 3 Approved For Release 2001/08/13 : CIA-RDP78BO4747A000900010016-5 'Approved For Release 2001/08/13 : CIA-RDP78BO4747A000900010016-5 I. PURPOSE OF STUDY The objective of this study is to determine the feasibility of a continuous film-to-film contact printer that uses open- gate techniques and has an output performance compatible with current state-of-the-art. Known factors contributing to degradation of image quality. in the system are to be analyzed. Specific attention will be paid to the problems of assuring film contact in the printer gate,,as well as possible advantages of using "liquid gate" techniques in the system. Also techniques for film cleaning will be evaluated. The study will be summarized in a test plan, which defines a program to evaluate experimentally the most promising approaches. II. ACTIVITY OF THIS REPORTING PERIOD A. EXPERIMENTAL PROGRAM Experiments were performed to evaluate the effects of contact- ing pressure, intermediate liquids, and diffusion in the illumi- nating system on output resolution. In order to perform the test, a 45.5X photoreduction of a USAF 1951 test target, on Eastman SO 105 emulsion,was used. The visual resolution threshold was 650 lpm with a microdensitometer contrast (AD) of 0.02, measured with an effective slit width of 0.3 micron. Approved For Release 2001/08/13 : CIA-RDP78BO4747A000900010016-5 Approved For Release 2001/08/13 : CIA-RDP78BO4747A000900010016-5 This target was then sequentially contact printed nine times through an Eastman 649-GH intermediate to produce an Eastman SO-132 9-target-array submaster. Final Visual resolution in the submaster ranged from 230 to 290 lpm. Microdensitometer cony, ranged from 0.10 to 0.18 at the limiting resolution. The submaster was contact printed onto Eastman SO-278 (Type 8430) in the test Getup shown in Fig. 1 under varying conditions of contact pressure, liquid gate, and source' diffusion. These conditions are given below. Presure: 0, 0.33, 2.12 psi. Liquid Gate: 90% Toluene, 107 "Freon-113" between submaster and film. Diffusion: ground glass, optionally inserted. The experiments were randomly reproduced to minimize system- atic errors, and output resolution was determined visually by two readers. The results are summarized in Fig. 2. Approved For Release 2001/08/13 : CIA-RDP78BO4747A000900010016-5 STATINTL Approved For Release 2001/08/13 : CIA-RDP78BO4747A000900010016-5 Approved For Release 2001/08/13 : CIA-RDP78BO4747A000900010016-5 Approved For Release 2001/08/13 : CIA-RDP78B04747A000900010016-5 $. TECHNIQUE EVALUATION We have surveyed conventional techniques broadly using pub- lished information, manufacturers' literature, patent data, and direct survey of photographic processors in the field. We have considered the following techniques for obtaining contact pressure: 1. Vacuum. 2. Air bearing. 3. Electrostatic attraction. 4. Adhesive and liquid gates. 5. Magneforming. 6. Hydraulic pressure. 7. Centrifugal force. We have considered the following techniques for dirt elimination: 1.' Air knife. 2. Vacuum. 3. Ultrasonics. 4. Electrostatics. 5. Solvent wash. In the liquid-gate study, we are considering the following problems: ` 1. Material compatibility. 2. Methods of application. 3. Methods of removal. Approved For Release 2001/08/13 : CIA-RDP78B04747A000900010016-5 Approved For Release 2001/08/13 : CIA-RDP78B04747A000900010016-5 III. PLANS FOR NEXT PERIOD We plan to complete our evaluation and prepare a.draft of the test plan to be submitted on this program. Approved For Release 2001/08/13 : CIA-RDP78B04747A000900010016-5