(SANITIZED) PHASE I REPORT ON THE KEYER MEMORY
Document Type:
Collection:
Document Number (FOIA) /ESDN (CREST):
CIA-RDP78-03424A002000010002-8
Release Decision:
RIPPUB
Original Classification:
C
Document Page Count:
68
Document Creation Date:
December 22, 2016
Document Release Date:
September 19, 2011
Sequence Number:
2
Case Number:
Publication Date:
November 30, 1960
Content Type:
MISC
File:
Attachment | Size |
---|---|
![]() | 2.15 MB |
Body:
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
CONFIDENTIAL,
L
PHASE I REPORT
?!% /Cc1 P
c 14-0 o 9" / -
r
t
November S 0~ 186
C
Submitted by:
roje,t Epgineer
Approved by:
25X1
Approves by:
25X1
r
CONFIDENTIAL
Manager, Program 684
Great Valley Laboratory
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
CONFIDENTIAL
I
II
INTRODUCTION . . . . . . . . . . . . .
CIRCUITS AND LOGICAL DESIGN . . . . . . .
MODES OF OPERATION . . . .
CIRCUIT DESIGN . . . . . .
Modified Coincident Current Memory . . . . . .
12
Power Supply . . . . . . . . . . . .
18
Mode Selector Switch Circuit . .
19
Keyer. . . . . . . . . . . . . . . .
21
Pulse Generators . . . . . . . . . . .
22
Driver and, Switch Circuits. . . . . . . .
23
Address Circuits .
25
Sense Amplifier . . .. . . . . . . . . .
27
Indicator. . . . ... . . . ... . .
27
27
Logic Circuits . . . . . . . . . . . .
29
TRANSMITTED CODE UNITS. .
Frequency Shift Keying . . .
31
CW Keying . . . . . . .
33
Adapter Cord Operation. . . . . . . . . .
33
CON H ENTIAI,
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
CONTENTS (Cont'd)
SECTION
PAGE
III MECHANICAL DESIGN . . . . . . . .
.37
DESIGN CONSIDERATIONS . . . . . . .
.
.
.
37
COVER . . . . . .. . .. . . . . .
Battery Mount . . .
40
Mode Selector Switch
40
Cable Plug Receptacle . . . . . .
40
Indicator. . . . . . . . . . . .
40
Keyer. . . . . . . . . . . .
.
.
.
41
GO and CLEAR Switches . . . . . . . .
41
CASE . . . . . . . . . . . .
IV CONCLUSIONS AND RECOMMENDATIONS .
BATTERY MOUNT . . . . . . . . . . .
.
.
.
46
MEMORY . . . . . . . . . . . .
46
CIRCUITS . . . . . . . . . . .
46
CASE . . . . . . . . . . . . . .
47
COVER AND KEYER. . . . . . . . . . . .
.
.
48
5-POSITION SWITCH . . . . . . . . . . .
.
.
.
49
GO AND CLEAR MONENTARY CONTACT SWITCHES.
.
.
.
49
PLUG RECEPTACLE . . . . . . . . . .
.
.
.
49
INDICATOR. . . . . , . . . . . . . D
o
e
s
49
iv
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
CONFIDENTIAL
CONTENTS (Cont'd)
APPENDIX PAGE
I DESIGN CRITERIA . . . . . . . . . . . . I- i
TEMPERATURE COMPENSATION . . . . . . . I- i
DRIVE VOLTAGES . . . . . . . . . . . . 1-5
LOGIC CIRCUITS . . . . . . . . . . . . . . 1-6
Switching Amplifier . . . . . . . . . . . 1-7
Timing Circuit . . . . . . . . . . . . . 1-7
C
I F) ENTIAL
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Weight and Power
Total Weight Less Batteries 3.8 lbs.
Case Weight 2.7 lbs.
Net Weight 1.1 lbs.
Equivalent Case Weight in Aluminum 0.9 lbs.
Net Weight 1.1 lbs.
Theoretical Total Weight 2.0 lbs.
Battery Drain
Function Switch Position D-C Current Milliampers Power Milliwatts
Standby (S) 218 544
Receive (R) 238 595
Idle (I) 230 575
Transmit (X) Standby 270 675
Transmit (X) Operating 240 600
Battery Source - Sonotone nickel cadium size D rechargeable
cells - terminal voltage 1.25 volts each.
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
LIST OF ILLUSTRATIONS
1. Keyer Memory. . . . . . ... . . . . . . . . . 2
2. NORTHVILLE Logic Symbols . . . . . . . . . . . . .. . 8
3. Keyer Memory Logic Diagram . . . . . . . . 10
4. Memory Configuration . . . . . . . . . . ... . 14
5. Current Time Relationships . .. . . . . . . . . . 16
6. Complementing Flip-Flop . . . . . . . . . . . . 24
7. One-Shot Multivibrator . . . . . . . . . . . . 28
8. AND Gate . . . . - . . . . . - . . . . . . . 28
9. Transistor OR Gate . . . . . . . . . . . . . . . 28
10. Diode OR Gate . . . . . . . . . . . . . . 30
11. Set Reset Flip-Flop. . . . . . . . . . . 30
12. aster Oscillator. . . . . . ... . . ... . . . 30
13. Frequency Shift Characteristics . . . . . . . . . . . . 34
14. FSK Adapter. Cord Circuit . . . . . . . . 36
15. CW Adapter Cord Circuit . . . . . . . . . . . . . 36
16. Keyer Memory Printed Circuit Card ... . . . . . . . 38
17. Arrangement of Printed Circuit Cards . . .. . . . . 42
18. Assembled Memory with Connections to
Printed Circuit Boards . . . . . . . ... . . . . . 49
19. Wired Memory Stick . . . . . . . . . . . . . 44
I-1 Switching Current Analysis Circuit . . ... . . . . 1-4
1-2 Drive Voltage Analysis Circuit . . . ... . . . . . 1-4
1-3 Switching Amplifier . . . . . . . . . . . . . . 1-8
1-4 Timing Circuit. . . . . . . . . . . . . . 1-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
LIST OF TABLES
PAGE
I Keyer Memory Specification .. . . . . .. . .. . . . 4
II Power-Supply Specification. . . . . . . ... . . 20
III Pulse Generator Specification. . . . . . . . . . . 24
IV Circuit Specification . . . . . . . . . . .
32
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
The Northville program covers the design, development, and fabrication of a Keyer
Memory unit which provides non-volatile storage of approximately 100 words of 6
characters each. The Keyer Memory is implemented through the use of low-cost,
solid-state circuits and a coincident-current, ferrite-core memory packaged within
the minimum volume practicable. Desired size of the unit is 6 inches x 1-1/2 inches
x 2-1/2 inches for a total volume of 31. 5 cubic inches. The above effort constitutes
Phase One of the program and is to culminate in the delivery of a Keyer Memory unit
for test and evaluation by the customer. Dependent on the results of the evaluation
a Phase II is planned to provide four additional units for service tests.
The original specification called for an 1800-bit buffer memory using the twistor
technique for storage. The disadvantages of larger volume, longer development time,
and higher cost of the twistor memory were outlined in a proposal submitted by
Burroughs. The additional possibility of increasing the capacity to 2500 bits in the
same volume with a ferrite-core, coincident-current memory resulted in a decision
to delete the twistor requirement when the program was funded.
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
The program was modified during the latter part of 1959 to provide for an integrated
Keyer Memory. Significant advantages in cost and volume were possible, primarily
through the elimination of duplicate circuit functions, power supplies, and structural
elements.
The Keyer Memory unit is a completely self-contained device permitting the manual
insertion of 2560 bits stored in a ferrite core memory. The information is stored
4 bits at a time by depressing any one of 12 keys on a keyboard integral to the Keyer
Memory. Through the incoming information has a character format identical to the
5-unit start/stop teletype code, only 4 units need to be stored to provide for the 12
characters used. The start baud is used only for control and the fifth and stop bauds
are not used. This gives a total character storage of 640 and a 6-character-per-word
storage of 106 2/3 words. Once the memory has had any number of words inserted
up to the maximum capacity, the entire contents can be read out of the Keyer Memory
at a nominal rate of 60 words per minute.
The read-out cycle, once initiated by the operator, is automatic and nondestructive.
As each character is transmitted to the external receiving device, the same character
is re-inserted into the memory. The entire memory can be completely cleared by
properly actuating three switch controls. The controls are electrically interlocked
to minimize accidental clearing.
The Keyer Memory (figure 1) measures 8 inches by 4 inches by 1-5/8 inches for a
volume of 52 cubic inches without batteries. The prototype weighs pounds including
2. 7 pounds for the brass case and cover. (The use of heavy material for the enclosure
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Table I. Keyer Memory Specifications
Volume
Component Count
Component Density
KE - 9 and
3
Buffer Memory
6 in x 1. 5 in x 3. 5 in = 31. 5 in
KE-9
3 5/16 in x 2 1/8 in x 7/8 in = 6. 2 in3
97
fi 2 = 15.5 per in3
Keyer Memory
8 in x 1 5/8 in x 4 in = 52 in3
4058
4058 = 78 components/in3
Keyer Memory
Less KE-9
3* 3
31. 5 in - 6. 2 in = 25.3 id
3961
2
63 = 157 components/in3
5
Original Specification
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
is discussed in the mechanical design section.) The average power dissipation is 600
milliwatts supplied by two D-size, Nicad batteries.
In table I the volumes, component counts, and component densities are tabulated for
various conditions. The specification furnished before the program was initiated
requested a volume of 31.5 cubic inches. Though this volume included both the buffer
memory and the KE-9 Keyer, the proposal submitted by assumed that the 25X1
31. 5 figure applied to the buffer memory only. The proposal included a design goal
of 100 components per cubic inch. The actual overall density came out to 78 com-
ponents per cubic inch and a total volume of 52 cubic inches. The volume of the
memory proper was originally estimated at 2 cubic inches and the actual volume is
1. 4 cubic inches.
The inability to meet the desired volume can be attributed largely to the extreme
temperature limits specified. The normal range with worst-case design of a ferrite
core memory is 55?C. The specification calls for a temperature range of minus
50?C to +50?C. Relaxing the worst case designs and changing the lower limit to minus
40?C kept the problem realistic but still made for difficult packaging. The temperature
range and high component density required considerably more component evaluation
than originally antici pated. Even the use of factory adjustments to remove initial
component tolerances did not provide sufficient relief to ease the packaging problems.
An Appendix on Circuit Design Criteria is included in this report. Certain schematic
diagrams referred to in the following, sections are provided under seperate cover.
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
CIRCUITS AND LOGICAL OPERATION
The Keyer Memory is designed to provide a system with simplicity, small physical
volume, low cost, and operation from low power. Information can be written into
the memory at random with the manual keys of the keyer and stored until required.
When memory information is required it can be transmitted sequentially at teletype
speed. Logic symbols used in the
program are described in figure 'g25X1
and the logic diagram is shown in figure 3.
MAJOR UNITS
The Keyer Memory is comprised of nine major units. The function of these units
is as follows:
1. Power Supply. The power supply is capable of converting either the
voltage of two series-connected dry cell batteries (3 volts) or the volt-
age of two series-connected Nicad batteries (2. 5 volts) to four regulated
and two unregulated voltages. Although designed for this capability, the
prototype Keyer Memory is set internally to operate only from Nicad
batteries.
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Output is -2V with 1 or more in-
OR Gate puts at -2V. OR gates have 2 to
4 inputs.
Output is -2V when all inputs are
-2V, No output when all inputs
are not at -2V. AND gates have
2 to 5 inputs.
A -2V input to either side will
Set-Reset produce a -2V output at the same
side. A -2V input to the other
Flip-Flop side will then reverse the state
of the flip-flop.
Complementing A +2V complement input reverses
the state of the flip-flop. The
Flip-Flop ZERO input is the reset input.
Output is the complement of the
input,
-2V input = OV output
OV input = -2V output.
Figure 2. I I Logic
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
2. Mode Selector Switch. This switch selects the desired mode of opera-
tion and connects the logic biases for the specific mode.
3. Keyer. The keyer consists of 12 manual keys and a decoder. In the
RECEIVE.(R) mode of operation the keyer is used to write information
into the memory; each key selects specific fixed information.
4. Logic Circuits. These circuits perform the required logical functions
for the selected mode of operation.
5. Address Circuits. The address circuits are a system of counters used
to address the memory to read and write memory information
sequentially.
6. Drivers. Driver circuits generate the currents necessary for switch-
ing the memory cores and, when properly addressed, deliver these
currents to the selected memory word.
7. Memory. The memory consists of 2560 ferrite cores (one core per
word) and associated selection diodes; each core stores 1 bit of
information.
8. Sense Amplifier. The sense amplifier detects the core outputs when
the memory is interrogated and amplifies these outputs to a usable
level.
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
POWER
CONVERTER
8 REGULATOR
START
FF
4-INFO
FF'S
1 011
0 010 100
WRITE
SW (4)
0 1 0 1 p l 0 1 O 1 0 1 0 1 ) 1 0 1 0 1 0 1 0 1 0 1
Figure 3. Keyer Memory Logic Diagram
1 ((( 1 1 1 1 I I I r (( I [
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
9. Output Buffer and Indicator. The output buffer provides buffered output
information to other equipment used with the Keyer Memory. The indi-
cator circuit, using an incandescent bulb, indicates when contact has
been made in depressing a key of the keyer, provides a rough indication
of proper operation during IDLE (I), and indicates the end of the mes-
sage during the TRANSMIT (X) mode of operation.
MODES OF OPERATION
Four modes of operation are used. The desired mode is selected by a 5- position
mode selector switch; the fifth position is OFF. Operation in each of these modes
is as follows:
1. STANDBY. Power converter on with biases applied to prepare the
equipment for operation.
2. RECEIVE. For writing information into the memory.
3. IDLE. Idling characters are generated (one START baud followed by
all marks).
4. TRANSMIT. This position permits reading information from and re-
storing information to the memory, and the clearing of the memory.
CIRCUIT DESIGN
Circuits of the Keyer Memory were selected from existing proven circuitry and
adapted to fill the requirements of the program. These circuits will operate within
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
a temperature range of minus 40 degrees Centigrade to plus 50 degrees Centigrade.
Satisfactory operation can be obtained when using as a primary source of power two
series-connected dry cells or two series-connected Nicad batteries, although the
prototype will use only Nicad batteries. End-of-life voltage for the series-connected
dry cells is 2. 2 volts; end-of-life voltage for the series-connected Nicad batteries is
1. 8 volts. The indicator lamp, which is connected across half of the battery voltage,
will function until the voltage across it falls below approximately 1. 2 volts. The in-
formation baud length at the output is 22 milliseconds, plus or minus 3 percent; the
STOP baud length at the output is 28 milliseconds, minimum.
A description of the selection of circuit design criteria is included as Appendix I to
this report.
Modified Coincident-Current Memory
In a conventional coincident-current memory three half-select currents are utilized;
an X current, Y current, and Inhibit current, each of which are half the value of
nominal switching currents. Reading is accomplished by the coincidence of X and Y
to give a full switching current at the X-Y intersection. Writing a ONE is accomplished
by the coincidence of negative X and Y currents. Writing a ZERO (not writing a ONE)
is accomplished by the triple coincidence of X, Y, and Inhibit currents.
If Ith is defined as the maximum current which will guarantee no core switching and
is is defined as the minimum current to ensure complete core switching, then the
memory current equations which must be satisfied are:
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
lx
Iy
The best switching- to- no- switching current (neglecting current tolerances) is there-
This use of a 1-bit word permits modification of these equations to obtain a 3-to-l
ration. Because of the 1-bit per word, there is no ONE and ZERO combination which
must be written at the same time; only a ONE or a ZERO. This permits X and Y
currents to be 2/3 switching currents, and the inhibit current (referred to as the
bias current) to be a negative 1/3 switching current. Therefore, during read,
'th (unselected cores)
'th (unselected cores)
> I (reading, or writing a ONE in the selected core).
s
Ith (unselected cores)
'th (writing a ZERO in the selected core), and
< Ith (unselected cores)
Ix + 'y - 'bias
< Ith (unselected cores)
Is (selected core)
The above equations are applied to negative currents during the writing of a ONE.
When writing a ZERO no currents are turned on, thereby eliminating the need for
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
8
DRIVERS
AND
SWITCHES
64
LINES
8
DRIVERS
AND
SWITCHES
Figure 4. Memory Configuration
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
an equation for this function. The 1/3 and 2/3 read currents as specified are sub-
stituted, resulting in:
2 / 3
- 1 / 3 =
1 / 3 (no- switching current)
2 / 3
- 1 / 3 =
1 / 3 (no- switching current)
2/3
+ 2/3
- 1/3 = 1 (switching current),
which gives the 3 to 1 ratio.
The configuration for this modified coincident-current memory is shown in figure 4.
The ferrite cores are arranged in a 64-by-40 matrix. An 8-by-8 driver switch de-
livers the X currents and a 4-by-10 driver switch delivers the Y currents. Bias
current is carried by a single line threaded through all the cores of the matrix.
Memory Selection. The memory selection scheme representation is shown in the
upper right in figure 3. The following description is of the Y drivers and switches,
since operation of the X drivers and switches is identical. For a particular address
in the address counters, one of the four outputs from the 5-DECODER will select
one of four Y-read drivers and the corresponding Y-write switch. One of the outputs
of the 10-DECODER will select one of the ten Y-write drivers and the corresponding
Y-read switch. The total number of lines that can be selected is therefore 10 times
4, or 40 lines. The Y-line current, (from the Y-current generator) is delivered to
the selected line. The drivers and switches are further selected by the output of the
output of the read-write flip-flop. When the flip-flop is in the READ (R) state, the
read drivers and read switches are selected. When the flip-flop is in the WRITE
(W) state, the write drivers and write switches are selected.
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Y CURRENT I
I I I I
I I I I I I
I I I I I I
I I
~`
(
X CURRENT I I r BIAS CURRENT I I I I I I
A2
r
Figure 5. Current Time Relationships
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Memory Operation. Beginning with the read cycle, the read-write flip-flop is in the
READ state, and the address counters are set to a particular count. Therefore, one
read driver and one read switch are energized in both the X and Y directions. Since
the bias driver is associated with all words, it is addressed only by the read-write
flip-flop; it also is set when the read-write flip-flop is in the READ state. An input
pulse, applied simultaneously to the X, Y, and.bias-current generators, produces
three current pulses. The time relationship of these current pulses is shown in
figure 5.
If the Y pulse is of amplitude, a,, and duration, T, then the X pulse is of amplitude, a,
and duration T + Al, and the bias pulse is of negative amplitude a/ 2 and duration
T +.A 2. If a/2 is approximately 1/3 switching current, then with the bias pulse
turning on first, there is a negative 1/3 noise current in all cores. When the X
pulse is turned on, a 2/3 - 1/3 = + 1/3 noise current is delivered to the selected X
line. When the Y pulse is turned on a 2/3 - 1/3 = + 1/3 noise current is delivered
to all cores in the selected Y line except one, which is the core in coincidence with
X and Y. This core receives 2/3 + 2/3 - 1/3 = + 1 (full switching current). If the
core was in the ONE state it is now switched to the ZERO state and the core output
produced is sensed by the sense amplifier. Turnoff of the bias generator triggers
the read-write flip-flop to the WRITE state but the address counters remain at the
same count.
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
During the write cycle, two conditions can occur. If a ZERO is to be written, the
input pulse is inhibited and no currents are generated. Since the core went to the
ZERO state during the read cycle, no currents are required during the write cycle.
In writing a ONE the same sequence is used as in the read cycle except that the
write drivers and switches are energized, delivering negative currents to the cores.
The currents produced, in the order of current generator turnon, are:
1. Bias. Plus 1/3 noise current in all cores
2. X Generator. Minus 2/3 + 1/3 = - 1/3 noise current in the X line
3. Y Generator. Minus 2/3 + 1/3 = - 1/3 noise current in the Y line, and
4. Minus 2/3 - 2/3 + 1/3 = 1 (full current) in the selected core. This core
is then switched to the ONE state.
In summarizing the operation, read current always exists, switching the selected
core to the ZERO state. Write current flows in the same addressed lines as read
current if a ONE is to be written. If a ZERO is to be written, turn on of all three
current generators is prevented.
Power Supply
The power supply is comprised of a dc-to-dc converter and four transistor regulators
and provides six rectified output voltages.' The dc-to-dc converter consists of a free-
running multivibrator transformer coupled to the rectifier circuits. Power to operate
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
the converter is supplied by batteries. . Four of the six rectified output voltages are
regulated by the transistor regulators; the other two voltages (plus 7 volts and minus
7 volts) are filtered but not regulated.
The outputs of the four regulated voltages (plus 2 volts, minus 2 volts, plus 5 volts,
and minus 5 volts) are controlled by Zener diodes. The output of a regulated voltage
is therefore Vout Vdiode - Vbe?
The frequency of the power supply oscillator is 30 kilocycles, plus or minus 10
kilocycles. For the remaining power supply specifications refer to table II. Drawing
4093-1004, contains the power supply circuit diagram.
Mode Selector Switch Circuit
The switch circuit consists of the mode-selector switch, ganged 5-position switches
and the gating necessary to provide the logical bias outputs (figure 3). Switch deck 1
(with shorting contacts) is used to connect power to the converter in all positions
except OFF. Switch deck 2 is used to apply either ground or plus 5 volts to the cur-
rent generators. Since the current generators are used only during the receive and
transmit modes the plus 5-volt supply is applied only in these positions.. Switch deck
3 connects the logical biases and the P pulse. The diode gates are all OR gates which
provide an output of minus 2 volts if only one input (minus 2 volts) is present. When
the switch is changed from one position to another a negative pulse is applied to a
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Table II. Power Supply Specifications
VOLTAGE
TOLERANCE
(volts)
MAXIMUM LOAD
(ma. )
+2.0V
?0.15
10.0
- 2.0 V
? 0. 15
10.0
+5.0V
?0.2
10.0
- 5.0 V
?0.2
25.0
+ 7.0 V
? 1.0
2.0
- 7. O V
? 1. 0
2.0
Regulated
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
one-shot multivibrator, producing a single output pulse P of approximately 35 micro-
seconds. Drawings 4093-1004 and 4093-1005 contain the Mode Selector Switch
Circuit Diagram.
Keyer
The keyer consists of 12 manual keys and a wired-core decoder. The decoder is
comprised of four flip-flops, a one-shot multivibrator, and gating. The keyer cir-
cuit diagram is contained in drawing 4093-1001.
Depressing a key causes a pulse of current to be sent through a particular wire (of
the wired core decoder) which passes through some combination of the core trans-
formers. Outputs of the core transformers are used to set the four information flip-
flops. The states of these four information flip-flops are then sensed serially by
their associated AND gates and the address inputs. The keyer information output
therefore is the serial output of the four information flip-flops.
All of the wires pass through the core transformer associated with the one-shot
multivibrator so that whenever a key is depressed, a keyer START pulse is generated.
The keyer START output is a negative pulse which goes from minus 0. 1 volt (plus or
minus 0. 1 volt) to minus 2. 2 volts (plus or minus 0. 3 volt). The pulse duration is
35 milliseconds, plus or minus 25 milliseconds.
Since the current pulse delivered to the wired-core decoder is the result of the
charge on a capacitor, a definite time must be allowed between breaking the contact
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
of one key and depression of the next key. If five time constants are allowed to permit
the capacitor to fully charge, the time separation is:
5 x 100'x 103 x 10-6 = 0. 25 seconds.
Pulse Generators
The plus 5-volt input from the mode-selector switch is present only during the
RECEIVE (R) and TRANSMIT (X) modes of operation. In other modes, this input
is at ground potential, preventing any transient from generating a current-pulse
output (figure 3). Drawing 4093-1039 contains the Pulse Generator circuit diagram.
The input to the pulse generators (from the logic circuits) is a negative pulse of
approximately 25 microseconds duration. This pulse is applied simultaneously to the
X-, Y-, and bias-pulse generators. Each pulse generator consists of two delay multi-
vibrators in tandem followed by two stages of current amplification. The bias pulse
generator has a 3. 5-microsecond delay multivibrator followed by a 7.5-microsecond
delay multivibrator. The 7.5-microsecond delay multivibrator generates the current
pulse which is amplified to full bias current.
The delays of the multivibrators associated with the X-pulse generator are 4.5 micro-
seconds and 5.5 microseconds; delays of the multivibrators associated with the Y-pulse
generator are 5.5 microseconds and 3. 5 microseconds. An input pulse to the pulse
generators therefore turns on all three generators, but not simultaneously. The bias
generator turns on first and turns off last. The X-pulse generator output is within
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
the bias-pulse time, and the Y-pulse generator output is within the X-pulse time.
The leading edge of the Y generator pulse is used to generate a strobe pulse for the
sense amplifier output. For specifications of the pulse generator refer to table III.
Driver and Switch Circuits
The purpose of the driver and switch circuits is to steer the current pulses of the X
and Y current generators through the proper X and Y memory-core lines in the proper
direction, and to steer the bias current in the proper direction through the bias winding
(figure 3). Drawing 4093-1007. contains the schematic for this circuit.
Considering first the X and Y drivers and switches, each driver and switch consists
of a current-steering transistor and a 2-input AND gate. The two inputs are the
address and the output of the read-write flip-flop. If both inputs are negative, the
base of the current-steering transistor is negative and the pulse current can pass
through this transistor. Because of the long delay (11 milliseconds) permitted to set
up these drivers and switches, a large capacitor is connected to the base of the
current-steering transistor. When current passes through the transistor, the base
voltage changes very little. Use of this capacitor minimizes the power required to
energize the drivers and switches. All of the driver circuits are clamped at minus
2 volts while the switches are not clamped. The gate inputs go from zero volts to
minus 5 volts. This places the base of the energized driver at minus 2 volts and the
base of the energized driver at minus 2 volts and the base of the energized switch at
minus 5 volts which puts a 3-volt drop across the selected line of cores through which
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Table III. Pulse Generator Specifications
GENERATOR
INITIAL
DELAY
PULSE
DURATION
OUTPUT
CURRENT
(2 RE)
RISE
TIME
FALL
TIME
Y
5.5(?0.4)
3.5(?0.4)
118ma.
0.2(?0.1)
0.6 sec.
psec.
psec.
(?9%)
psec.
max.
X
4.5(? 0.4)
5.5(? 0.4)
118 ma.
0. 2(? 0. 1)
0. 6 sec.
psec.
psec.
(? 9%)
psec.
max.
Bias
3.5(? 0.4)
7.5(? 0.4)
68 ma.
0. 2(t 0. 1)
0. 6 sec.
psec.
psec.
(? 9%)
psec.
max.
Note: The output current should have a temperature coefficient of approximately
minus 0.45 percent per degree Centigrade.
Figure 6. Complementing Flip-Flop
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
the pulse current passes. For this reason the address and read-write flip-flop outputs
are zero to minus 5 volts. All other signal voltages in the system are from zero to
minus 2 volts.
Operation of the bias drivers and switches is similar to the X and Y drivers and
switches with one exception. There is only one bias line, and current passes through
this line independent of the address. There is, therefore, no address input to the
bias drivers and switches.
Output current of the X and Y drivers at 25?C is 118 milliamperes, plus or minus 9
percent. Output current of the bias driver at 25?C is 64 milliamperes, plus or minus
9 percent. The base voltage rise during a current pulse is 1. 0 volt, maximum.
Address Circuits
The addressing circuits consist of 13 complementing flip-flops in tandem (figure 3).
Drawing 4093-1006 contains the schematic for the address circuits. The basic cir-
cuit of a complementing flip-flop is shown in figure 6.
A positive input pulse will reverse the state of the flip-flop. If transistor Q1 is on
and Q2 is off, the collector of Q2 is at minus 5 volts. The anode of the steering
diodes associated with Q2 will also be minus 5 volts. The collector of Q1 will be
near ground potential as well the anode of its associated steering diode. A positive
pulse input will have no effect on Q2 provided the pulse is less than 5 volts but it will
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
turn off Ql which in turn turns on Q2.. Conditions will then reverse and the next posi-
tive input pulse will turn off Q2, and so on.
The first three flip-flops in the address counter are used to count five pulses and
then reset to the starting position although they are capable of counting to 8 (23).
When the fifth count is reached, a diode decoder sends a negative output to circuit
A, (drawing 4093-1006) which resets the three flip-flops to the starting condition.
The next four flip-flops, although capable of a count of 16 (24), are used to count 10.
A similar circuit (A) is used here to reset these four flip-flops after 10 counts. The
next 3 flip-flops count 8 (23), and the last three flip-flops also count 8. No internal
resetting is required as these flip-flops are used to their full counting capability.
The diode decoders associated with the address flip-flops are used to produce, for
a given address:
1. One negative and four positive outputs from the first three flip-flops
(5-DECODER).
2. One negative and nine positive outputs from the next four flip-flops
(10-DECODER).
3. One negative and seven positive outputs from the next three flip-flops
(8-DECODER).
4. One negative and seven positive outputs from the next three flip-flops
(8-DECODER).
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sense Amplifier
The sense amplifier consists of two stages of differential amplification followed by
single-ended output (figure 3). Drawing 4093-1005 contains the schematic for this
circuit. The purpose of the differential stages is to reject common mode noise. For
gain stabilization a considerable amount of degeneration is used in the first two stages.
This amplifier will give a negative output for either positive or negative input signal.
Also associated with the sense amplifier is a 1-transistor multivibrator which
generates the strobe pulse, and a 5-input AND gate which controls the sense amplifier
output so that it is fed to other circuitry only at the proper times.
Indicator
The indicator circuit consists of a combination of AND and OR gates followed by a
buffer stage which activates the indicator light. When activated, the light is con-
nected across one of the two batteries used for primary power (figure 3). Drawing
4093-1005 contains the schematic for the indicator circuit.
One-Shot Multivibrator
The input to the standard one-shot circuit is a negative pulse, the duration of which
need only be sufficient to permit feedback action (figure 7). The duration of the
negative-going output pulse is dependent on the RC time constant.
The one-transistor multivibrator requires a positive input pulse (negative for an
NPN transistor), the duration of which must be longer than that of the output pulse.
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Figure 7. One-Shot Multivibrator
+ 2V
Figure 9. Transistor OR Gate
-5V
A OUTPUT
o---t*--
e 0----D4
Figure 8. AND Gate
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
(The output pulse is a function of the RC time constant.) If the input pulse is shorter
than the calculated RC output pulse, the output will be of the same duration as the
input pulse; it can never be longer than the input pulse.
Logic Circuits
This section describes the operation of circuits which comprise the logical elements.
Logic circuit specifications are given in figure 2.
AND Gate. A negative output (figure 8) of minus 2 volts is obtained only if all inputs
are at minus 2 volts. If one or more inputs are at zero volts, the output will be zero
volts.
OR Gates. If one or more inputs (A, B, or C) are at minus 2 volts the output will be
minus 2 volts. If all inputs are at zero volts the output will be at zero volts, figure
9 illustrates a transistor OR gate and figure 10, a diode OR gate.
Set-Reset Flip-Flop. A negative input at A of sufficient length to permit regeneration
will set the flip-flop to the ONE state (figure 11). A negative input is required at B
to reset the flip-flop to the ZERO state.
Complementing Flip-Flop. Complementing flip-flops are used in the address circuits.
The circuit (figure 6) and description are covered under Address Circuits in this
chapter.
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Figure 10. Diode OR Gate
Figure 11. Set, Reset Flip-Flop
Figure 12. Master Oscillator
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Master Oscillator. The master oscillator is a free-running pulse oscillator (figure
12). The output pulse duration is proportional to NE (the number of turns in the
collector winding times the magnetic flux divided by the voltage across the winding);
the pulse repetition rate is proportional to the base-circuit RC time constant. A 50-
microsecond pulse is produced every 176 milliseconds. An additional output winding
(not shown here) is shown in the logic diagram as an inverter between the master
oscillator and AND gate 13. For pulse specifications refer to table IV.
Output Buffer. The output buffer circuit consists of an integrator and three stages
of current amplification. The integrator removes the short duration pulses which
exist between each baud as produced by the output flip-flop. The Xl logic bias input
to the output buffer (figure 3) prevents turnon of the last two stages except in the
TRANSMIT and IDLE modes of operation. Drawing 4093-1005 contains the schematic
of the Output Buffer.
TRANSMITTED CODE UNITS
Two types of transmission are provided, frequency shift keying (FSK) and continuous
wave (CW). The type keying to be used determines the selection of adapter cords
but does not otherwise affect operating procedures of the Keyer Memory itself.
Frequency Shift Keying
Spaces appear at the higher of the two carrier frequencies and marks at the lower
frequency.
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Table IV. Circuit Specifications
CIRCUIT
OUTPUT
PULSE
PULSE
DURATION
MISC.
Oscillator)
2.1 V
50 ;A sec,
Rep. Rate
+ 0.25 V
+ 20 ?sec.
176 msec.
+ 30 msec.
11 - Msec
- 2.1 V
11.0 msec.
Multivibrator
+ 0.2 V
+ 3.0 msec.
Start
- 2. 0 V
50 ?sec.
Buffer
+ 0.2 V
+ 10 ;A sec.
_
One-Transistor
- 2.1 V
25 ?sec.
One-Shot
+ 0.2 V
+ 5 ?sec.
_
Multivibrator2
25 - Msec
- 4. 0 V
15 msec.
Multivibrator
+ 0.3 V
minimum
_
Read-Write
Note 3
Note 3
Counter, Input Buffers
-
End-Around Buffer
- 2. 0 V
15 ?sec.
_
+ 0.2 V
+ 5 ?sec.
Address Flip-Flop
- 0.3 V. + 0.2 V
or
-
-
- 5.2V, +0.3V
Address Circuit "A"
+ 3.5 V
300 IA sec.
+ 0.4 V
+100 IA sec.
_
Sense Amplifier4
- 2. 0 V
1.5 ?sec.
Strobe Output
(Input 40 to 150 mv)
+ 0.2 V
+0.5 psec.
-2. 0 V, + 0.2 V
2.5 ?sec.
+0.5 ?sec.
Indicator5
Visual
Indication
_
Output Buffer
50 ma.
(to load RT-6)
-
Notes:
1.
One positive and one negative output pulse.
2.
This circuit follows the 11-msec. multivibrator.
3.
Inversions of the output of the one-shot multivibrator which follows the
first 11-msec. multivibrator.
4.
Maximum input noise (for no output) is 24. 0 mv. Minimum input
signal required is 40. 0 mv.
5.
Requires input of -2. OV, 10 msec. minimum. Minimum voltage
required across indicator light is 1. 1 volt.
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Figure 13 shows the frequency-shift characteristics of CR-18 and CR-27 crystals.
Although the amount of shift varies between different units cut to the same frequency,
a given crystal can be expected to retain a given approximate shift permanently.
Number CR-18 or CR-27 crystals have been encountered which display frequency
shift of too small a value for reception on standard equipment. When doubling or
tripling in the transmitter the frequency shift transmitter will be correspondingly
doubled or tripled and shifts as great as 3000 cps could result. One method for
receiving shifts greater than 1000 cps is to zero-beat the receiver BFO on the "mark"
carrier frequency and treat the result as if it were CW keying. Another method is to
set receiver selectivity to minimum value and tune in on the mark carrier. Perhaps
the best practice is to pre- check the desired crystals for shift, and if doubling or
tripling would cause shifts greater than 1000 cps, use the CW Adapter Cord for
transmitting. Use of CW keying would not provide the 3 db advantage of FSK.
The frequency shift of the transmitting crystal does not vary with the battery voltage
of the Keyer Memory, but ?10 percent voltage fluctuations of the transmitting power
source may cause variations of ?2 percent.
CW Keying
The transmitter is keyed off only during spaces and remains on during marks.
Adapter Cord Operation
Both the FSK and CW adapter cords contain semiconducter circuits within the black
plastic encapsulation and should be regarded as parts of the Keyer Memory.
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
FSK Adapter Core. A Varicap semiconducter diode is paralleled through a small
capacitor with the transmitting crystal (figure 14). During transmission of a space,
a d-c voltage, obtained from rectification of rf by the Varicap itself is permitted to
appear across the Varicap. This voltage, whose magnitude is limited to about 10
volts by a resistor, causes the Varicap to assume minimum capacitance. During a
mark, the output amplifier shorts the d-c voltage through an r-f choke, thereby in-
creasing the varicap capacitance and dropping the crystal frequency.
CW Adapter Cord. When the CW adapter plug is inserted in the KEY JACK of the
transmitter, certain cathode returns in the transmitter are broken and placed in
series with the silicon power transistor in the adapter plug (figure 15). During a
mark, this transistor is saturated by current from the output amplifier, keying the
carrier on. During a space, the transistor is cut off. This interrupts the cathode
returns in the transmitter, keying the carrier off.
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
U
PIA
r
i
~r
L
R29
4K
L I C25
1 m h 33?uf
-LC24 R30
T?1,yuf 39K
* VARICAP
I A I TO TRANSMITTER
Figure 14. FSK Adapter Cord Circuit
NOTE: P3 IS A MODIFIED PL-55 TYPE PLUG
A= TIP, B = SLEEVE
J
Figure 15. CW Adapter Cord Circuit
B
I
CRYSTAL SOCKET
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
MECHANICAL DESIGN
The entire Keyer Memory is contained within a single metal case (figure 1). All
operating necessities are mounted on the cover and are secured to the underside of
the cover with the exception of the cable plug receptacle which is secured to the side
of the cover, and the battery mount which is secured to the top of the cover.
DESIGN CONSIDERATIONS
The Keyer Memory was made to the present mechanical configuration for the reasons
following. When the packaging design was initiated late in 1959 the circuitry had not
been entirely defined in terms of components and component values. The smallest
commercially available components and special mechanical parts, printed circuit,
and memory and interconnecting wires were used so that characteristics of these components
could be evaluated. It was considered desirable to arrange circuitry on printed cir-
cuit boards in organized groups closely related to one another, but not to develop
many small modules which would entail excessive interconnecting circuitry. To
attain desirable packaging density the decision was made to stack components on each
printed circuit board to a depth equal to the thickness of the largest single component
(approximately 0. 1875 inch). In planning component locations on a board, considera-
tion was given to sufficient space for the use of heat-sink tweezers and thin soldering-
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
iron tips during assembly. Printed circuit boards were planned as large as practic-
able to reduce the number of boards and the number of interconnections between
boards.
The present form of the Keyer Memory may be described as a hybrid, semi-modular,
organized-circuit design. Random interconnections were provided between the dis-
tant points of circuitry. Component boards were originally to be 0. 031-inch thick
to conserve space but warpage during soldering was sufficient to defeat this purpose.
Therefore, boards made after 1 May 1960 are 0. 062-inch thick: figure 16 shows the
high package density of a printed circuit board.
COVER
The cover can be removed from the case by removing the retaining screws and
lifting the cover off. The following items are attached to the cover and can be seen
when the cover is removed:
1. Mode selector switch assembly.
2. Cable-plug receptacle, with case grounding lug.
3. Indicator light assembly.
4. Keyer assembly.
5. GO and CLEAR pushbutton assemblies.
6. Power supply oscillator board.
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Battery Mount
The battery mount, located on top of the cover, has been designed to fold flat against
the cover when the batteries are removed; the ends of the mount (when folded) should
be locked in place with the slides provided for the purpose. Battery polarity is
inscribed on the battery mount.
Mode Selector Switch
This switch was designed as a flat, 5-position slide switch to save space. Careful
consideration was given to selection of contact material to ensure a reasonable long
operating life. The moveable portion of the switch is a notched shaft or stem, which
is pushed into or pulled out of the Keyer Memory to select the desired mode of
operation. Contact fingers attached to the shaft make connection with contacts on the
printed circuit portion of the switch. These contacts are rhodium plated, contact
fingers on the shaft are gold plated. Markings on the shaft indicate the mode position.
Cable Plug Receptacle
The plug receptacle used with the Meyer Memory is a duplicate of the model furnished
by the customer and is located on the side of the cover. The plug can be inserted only
in a manner ensuring proper polarity.
Indicator
The indicator consists of a miniature incandescent low-voltage lamp housed within
a plexiglass body. The plexiglass body has been designed to provide maximum
illumination through the convex lens on top.
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Keyer
Keyer switches used were furnished by the customer and are recessed in the cover.
Conservation of space, ease of operation, and accessibility for wiring were factors
determining their location on the cover.
Go and Clear Switches
These are miniature pushbutton switches. To avoid projection above the top surface
of the Keyer Memory, these switches have been recessed in the cover.
CASE
The remaining assemblies of the Keyer Memory are contained within the case. Be-
cause of machineability, ease of soldering, and ability to take a good finish coating,
brass was selected as the case material. Assemblies within the case are shown in
figure 17 and consist of:
1. Sense amplifier and associated circuit board.
2. Memory assembly.
3. Address boards assembly.
4. Power supply board.
5. Logic boards assembly.
All of the assemblies are fastened either to one another or to the case and are inter-
connected in a? manner permitting limited disassembly for test purposes. Where
necessary, either mylar or silicon-rubber sheets have been positioned between
assemblies to prevent possible short circuits. Where required, sensitive circuits
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
have been shielded by thin foils of special metal to prevent magnetic noise or high-
frequency radiation which might affect performance. Connections between assemblies
are made with insulated wire. The function and operation of the circuits of these
assemblies are described under CIRCUIT DESIGN.
The memory assembly consists of the memory matrix, the board containing the Y
switches and drivers, the two boards containing the X switches and drivers, and the
board containing the pulse generators and keyer circuits is located on the top of
the assembly. Figure 18 shows the configuration of the memory and its connections
to the printed circuit boards and figure 19 shows a wired memory stick.
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
0
Figure 18. Assembled Memory with Connections to Printed Circuit Boards
F'ig'ure 19. Wired Memory Stick
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
CONCLUSIONS AND RECOMMENDATIONS
The Keyer Memory was designed as a working prototype,. around components and
circuitry of known reliability. While not fabricated to pass any stringent MIL tests,
it was designed with MIL specifications in mind, especially in choice of components.
Continued satisfactory operation is expected within the temperature range specified
under CIRCUIT DESIGN.
Last-minute changes, dictated by improvements made in circuit design, caused
excessive component density in the areas of the sense amplifier circuit board and the
circuit board containing the pulse generators. Packaging in these areas should be
improved.
Recommendations made in the following,discussions should result in a Keyer Memory
which is even more compact, reliable, and rugged. Time and funds -did not permit
incorporation of these improvements into the prototype Keyer Memory. Recommen-
dations should be evaluated on the basis of the number of additional units required and
conditions under which the units will be operated.
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
BATTERY MOUNT
The battery mount is of conventional design and involves the use of individually installed,
loose batteries. These loose batteries could deteriorate before being put into use. It
is recommended that a special plastic case be provided which can be opened for re-
charging and inspection and which can be plugged, as a unit, into a connector on the
cover. This would permit a more dust-proof and water-tight construction.
MEMORY
The memory matrix should be redesigned to provide a simpler and less costly method
of assembling cores into strips. Redesign should also include more rugged core windings,
connections to core windings which are more readily accessible and easily soldered,
and a more positive method of assembling core strips into a matrix.
CIRCUITS
The use of more silicon transistors, although expensive, would result in a reduction in
leakage current. This would in turn result in a reduction in the number of clamping
diodes required. The net result would be reduction of over-all current requirements,
a reduction in the component count, and simplification of some of the circuitry. Minia-
ture flexible circuitry could be used between individual assemblies for increased reli-
ability.
Redesign might include development of a number of modular subassemblies to be used
for individual circuits which are repeated a sufficient number of times to make modulari-
zation economical.
46
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
It is recommended that circuits be physically revised to reduce connections and
thereby reduce joint failures during assembly and operation. All printed circuit
boards should be of 0.062-inch-thick laminated material for increased rigidity.
Printed circuit board assemblies. should be revised to take advantage of physically
smaller components which are becoming commercially available. Diode boards,. for
example, could be redesigned to take advantage of microdiodes and simplify the com-
plex wiring connections. Revision of board assemblies would result in considerable
reduction of board area without an increase in assembly cost or a loss in reliability.
An alternate approach to revision could be utilization of Bimag* (magnetic core) cir-
cuits which would simplify circuit design, increase reliability and possibly result in
a reduction of volume.
If the unit is to be capable of satisfactory operation under adverse field conditions,
ultimate redesign should be combined with an extensive test program. This would
ensure that each component, circuit, assembly or module, and the entire unit is capable
of meeting applicable MIL specifications.
CASE
The case for the first unit was made of brass to permit last minute modifications.
These modifications were unavoidable because of the limited design time allotted to
the entire project. The case was large for the same reason. Cases of future units
*A Burroughs-developed bistable magnetic-core technique
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
can be made smaller and of aluminum or another lighter material. If results of r-f
radiation studies permit, the case may be made of a suitable plastic. Redesign will
include consideration of molding or diecasting. Preliminary studies of redesign of the
memory and diode matrix for greater reliability and ease of assembly and test, and
of address and logic circuits for Bimag (magnetic core) application, indicate the pos-
sibility of at least 12. 5-percent reduction in case volume.
COVER AND KEYER
The present layout of the cover indicates the availability of space for a larger keyboard
(which would undoubtedly be easier to operate). The keyboard, as furnished by the
customer, is too compact to permit satisfactory manipulation of keys and it is neither
dust nor moisture proof. No provisions have been made for attachment of the keyboard
to the case as an assembled unit. It must be disassembled and attached to the case
piece by piece. This creates difficulty in making the necessary alignment and in
ensuring proper tension of each contact spring.
Tests of the keyer contact assembly disclosed a great degree of unreliability caused by
ganging of weak contacts in close proximity on a common plate which is easily affected
by changes in tension of mounting screws. Contact springs are too weak to properly
support and return the keys.. Spring strength decreases rapidly, resulting in a change
in length of the operating stroke. In addition, the bodies of the keys are too short for
the travel required to operate most of the contact springs. It is recommended that the
keyboard be, redesigned for more satisfactory operation, greater reliability, and con-
sideration of human factors principles.
48
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
5-POSITION SWITCH
Design criteria for this switch is based on the utilization of the small volume available
for the switch within the present case. The present switch is neither dust nor moisture
proof and its reliability has not been determined. Because of the importance of this
switch to the overall operation it should be redesigned for reliability and ease of use.
GO AND CLEAR MOMENTARY CONTACT SWITCHES
These switches were obtained through commercial channels.and were selected for their
small size and reliability. Some thought should be given to a selection of more rugged
switches, because of the importance of these switches to the performance of the Keyer
Memory.
PLUG RECEPTACLE
This device is basically the same as that used in the customer's sample and was used
without modification because it must be mated with the customer's plug. It should be
redesigned to provide a dust and moisture proof connection.
INDICATOR
At present, there is no means for indicating when the memory is full or nearly so.
With some redesign and the addition of several components (dependent upon the desired
stopping place) a steady light indication could be provided at any character, for example
character 635. This would inform the operator that he was close to filling the memory
and would aid in preventing overfilling of the memory.
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
An additional bulb, paralleled with the present bulb, would have two advantages.. First,
more light would be provided which would alleviate the present situation where indica-
tions may be missed due to insufficient light.. Second, a fail-safe would be provided
if one bulb failed. The use of an additional bulb would require some redesign and would
be an additional drain on the power supply.
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Design criteria presented here covers core-switching currents, temperature com-
pensation, drive line voltages, and logic circuits. Logic circuit design criteria
applies to the switching amplifier and timing circuit.
CORE SWITCHING CURRENTS
In establishing criteria for core switching currents it was.first necessary to make
certain assumptions. The basic circuit used in establishing criteria is shown in
figure I-1. Assumptions made were:
1. Initial adjustment of Re with respect to the plus 5-volt supply will give
a total error of plus or minus 2 percent.
APPENDIX I
DESIGN CRITERIA
2, Parameters Vbe2 and Vicel vary oppositely with temperature changes.
The difference between these parameters can be incorporated in calcu-
lation of the temperature coefficient of Re but can be disregarded when
considering design tolerances.
Based on these assumptions
Ic 2 =
(5v - Vbe2 - Vicel)a2
Re
(1)
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
IL = Ic2 a3 (2)
Using
S (Vbe2 and Vicel = f 3 percent
8 a2 = ?,2 percent
8 a3 = ? 2 percent
initial adjustment of Re = ? 2 percent
the total 8 IL will be ? 9 percent.
If in design the maximum noise currents are equal, and if
(3)
shown mathematically as
Ii(1.09) = I2(1.09) - Ii(0.91)
21l= 1.09 I2
1.09 12
0.545 I.,.
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Minimum signal current therefore, is
=2xI2-I1
= 2(0.91 I2) - 1.09 (1 =) 12) = 1. 226 12,
(4)
maximum noise current is
In = 1.09
(1. 09 12) = 0. 595 12,
and the worst-case signal-to-noise current ratio is
1.226 12
'y = = 2. 06
0. 596 12
(5)
(6)
TEMPERATURE COMPENSATION
To maintain a constant core output over the temperature range of minus 40 degrees
Centigrade to plus 50 degrees Centigrade, the drive currents. are. required to have a
temperature coefficient of minus 0. 45 percent per degree Centigrade.
The change in drive current caused by the effect of temperature variation on Vbe
(figure I-1) is 0.045 percent per degree Centigrade. The change in drive, current
caused by the effect of temperature variations on the plus 5-volt supply is minus
0. 022 percent per degree Centigrade. Therefore Re must have a temperature co-
efficient of - 0. 45 + 0. 045 - 0. 022 = 0. 022 = - 0.473 percent per degree Centigrade.
Assuming Rl in parallel with it has a temperature coefficient of zero, then
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
I IN
ILOAD
Figure I-1. Switching Current Analysis Circuit
Figure 1-2. Drive Voltage Analysis Circuit
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
making
R1R2 0.473
R2=.~.
R1 + R2 0.545
R1= 6. 57 R2
If R2 is two 68-ohm sensistors in parallel (34 ohms), than
R1 = 6.57 x 34 = 220 ohms
(7)
DRIVE VOLTAGES
Drive voltage criteria is based on the circuit configuration of figure I-2.. This cir-
cuit is representative of a word line of the memory.
Drive lines can be defined as having:
line inductance, L = 0. 75 microhenries
series resistance, R = 2. 0 ohms
core voltage per line VM = 0.465 volts
diode voltage, VD = 0. 8 volt during steady-state conduction and
= 1. 0 volt transient
Vbe of transistor Q2 = 0. 7 volt during steady-state conduction and
= 1. 0 volt transient.
With a load current, IL, of 150 milliamperes with a 0. 15-microsecond rise time
150x10-3
VL = 0. 75 x 10-6 x 0.15x10 6
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
VR = 0. 3 volt.
Under transient conditions the voltage drop across the word line is
Vdrop = Vbe(tran) + L di d + VO(tran)
(8)
Vdrop = 1. 0 + 0. 75 + 1. 0 = 2. 75 volts,
and steady-state voltage drop across the word line is
Vdrop = IR + VM + VD + VBK
Vdrop = 0.3 + 0.46 5 + 0. 8 + 0. 7 = 2.3 volts.
Therefore, the use of minus 2 volts on the driver and minus 5 volts on the switch re-
suits in a worst-case driver line voltage (allowing for tolerances) of
4. 8 - 2. 1 = 2. 7 volts.
This is an acceptable value.
LOGIC CIRCUITS
Logic circuit criteria explained here applies to the switching amplifier and timing
circuit. These are basic building blocks for the logic circuits covered in other chap-
ters of this report.
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Switching Amplifier
The basic switching amplifier circuit is shown in figure 1-3. In this circuit, where
load current always flows out of the amplifier, Rc is required only to absorb tran-
sistor ICO0
The value of Rc is calculated under conditions when the transistor is off, as
Rc=3v Ico?
When the transistor is on load current can be calculated as
Iload = 5v. I.L
5v
+ Is(diode) +
"load
(10)
Minimum base current is then calculated as
Ib=IL A
The value of the base biasing resistor. (R) is. calculated to be capable of supplying. max-
imum Ico from base to collector when the transistor is off.
Timing Circuit
The basic timing circuit is shown in figure 1-4. This is the basic building, block around
which the logic timing circuits were designed.
With load current equal to
v RL
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
-2V
Figure 1-3. Switching Amplifier
Figure 1-4. Timing Circuit
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424AO02000010002-8
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8
CONFIDENTIAL.
lb =IL
RT = 5v Ib.
(12)
For a given input voltage (Vin) and neglecting the base-to-emitter diode drop of the
Vin =(5+V )(1-eRTC)
t
eRI
5 + Vin
5+Vth
t = RTCJn 5
Since the leakage (base to collector) is relatively high in germanium transistors,
(13)
(14)
silicon transistors are used where accurate timing is required. Where timing ac-
curacy is not as critical, germanium transistors are used and the base current is
set to at least four to five times greater than Ico so that variations in this current
do not adversely affect the timing.
.:-NTIAL
Sanitized Copy Approved for Release 2011/09/19: CIA-RDP78-03424A002000010002-8