OPERATING AND SERVICE MANUAL, MODEL 410C ELECTRONIC VOLTMETER
Document Type:
Collection:
Document Number (FOIA) /ESDN (CREST):
CIA-RDP70B00584R000100280001-3
Release Decision:
RIFPUB
Original Classification:
K
Document Page Count:
65
Document Creation Date:
December 12, 2016
Document Release Date:
April 4, 2001
Sequence Number:
1
Case Number:
Publication Date:
February 1, 1963
Content Type:
BOOK
File:
Attachment | Size |
---|---|
CIA-RDP70B00584R000100280001-3.pdf | 4.04 MB |
Body:
Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
OPERATING AND SERVICE MANUAL
(hp PART NO. 410C-903)
MODEL 410C
ELECTRONIC VOLTMETER
SERIALS PREFIXED: 433
Appendix C, Manual Backdating
Changes adapts this manual to
Serials Prefixed:
311, 328, 339 and 344
Copyright Hewlett-Packard Company 1963
01556-3 Printed: FEB. 1965
Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
Caution
ONE SIDE OF ALMOST ALL POWER DISTRIBUTION SYSTEMS IS
GROUNDED. EXTREME CAUTION MUST BE USED IF DIRECT
MEASUREMENT OF POWER LINE VOLTAGES IS ATTEMPTED.
IF THE GROUND CLIP LEAD IS ACCIDENTALLY CONNECTED TO
THE UNGROUNDED SIDE OF THE LINE, SEVERE DAMAGE TO
THE 4 1 OC IS POSSIBLE BECAUSE OF THE SHORT CIRCUIT
CREATED. POWER LINE VOLTAGES CAN BE SAFELY MEASURED
BY USING THE PROBE TIP ONLY. CONTACTING THE GROUNDED
POWER CONDUCTOR WILL GIVE A READING OF 0 VOLTS WHILE
CONTACTING THE UNGROUNDED LEAD WILL GIVE FULL LINE
VOLTAGE READING.
Model 410C
Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3 01556-1
Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
Model 410U Table of Contents
List of Tables
TABLE OF CONTENTS
Section
Page
Section
Page
I GENERAL INFORMATION
1-3
V MAINTENANCE
5-1
1-1. Description
1-3
5-1. Introduction
5-1
1-4. Instrument Identification
1-3
5-3. Test Equipment Required
5-1
1-6. Accessories Available'
1-3
5-5. Performance Checks
5-1
5-7. Alternate Voltage Source
5-1
Section
Page
5-9. Mechanical Meter Zero
5-1
II INSTALLATION
2-1
5-10. DC Voltmeter Operation
5-1
2-1. Inspection
2-1
5-13. DC Ammeter Operation
5-2
2-3. Installation
2-1
5-16. Ohmmeter Operation
5-4
2-5. Rack Mounting
2-1
5-17. Amplifier Operation
5-4
2-9. Three-Conductor Power Cable
2-1
5-21. DC Amplifier Output Impedance
2-12. Primary Power Requirements
2-1
Check
5-5
2-14. Repackaging for Shipment
2-2
5-22. AC Voltmeter Operation
5-5
5-26. Adjustment and Calibration Proce-
Section
Page
dure
5-7
III OPERATION
3-1
5-28. Chopper Frequency Adjust
5-7
3-1. Introduction
3-1
5-29. Power Supply Adjustment
5-7
3-3. Adjustment of Mechanical Zero. .
3-1
5-30. DC Zero Adjustment (Bias) . . .
5-7
3-5. Front and Rear Panel Description
3-1
5-31. Ohms Adjust (R3)
5-7
3-7. Operating Procedures
3-1
5-32. AC Zero Adjust
5-8
3-9. DC Voltage Measurements
5-33. AC Full Scale Adjust (.5 v Range) .
5-8
(Figure 3-2)
3-1
5-34. DC Amplifier Output Adjust . . . .
5-8
3-11. DC Current Measurements
5-36. Troubleshooting Procedure
5-8
(Figure 3-3)
3-1
5-45. Servicing Etched Circuit Boards. .
5-9
3-13. AC Voltage Measurements
5-48. Chopper Assembly Installation. . .
5-10
(Figure 3-4)
3-1
3-15. Precautions When Measuring AC
Voltage
3-28. Negative Pulses
3-31. Measuring Resistance (Figure 3-7)
3-33. Measuring DC Nano-Ampere Cur-
rent (Figure 3-8)
3-1
3-4
3-4
3-4
Section
VI REPLACEABLE PARTS
6-1. Introduction
6-4. Ordering Information
6-6. Non-Listed Parts
Page
6-1
6-1
6-1
6-1
Section
Page
Appendix
IV THEORY OF OPERATION
4-1
A CODE LIST OF MANUFACTURERS
4-1. Overall Description
4-1
4-4. Circuit Description
4-1
Appendix
4-5. Input Network
4-1
B SALES AND SERVICE OFFICES
4-16. Modulator-Demodulator
4-1
4-23. The Feedback Network
4-2
Appendix
4-27. Power Supply
4-2
C MANUAL BACKDATING CHANGES
LIST OF TABLES
Number
Page
Number
Page
1-1.
Specifications
1-2
5-6.
AC Accuracy Test
5-6
3-1.
Possible Error When Measuring Voltage
5-7.
Power Supply Test
5-7
of Complex Waveforms
3-3
5-8.
AC Full Scale Adjust
5-8
5-1.
Recommended Test Equipment
5-0
5-9.
Front Panel Troubleshooting Procedure. .
5-11
5-2.
DCV Accuracy Test
5-2
5-10. Troubleshooting Procedure
5-12
5-3.
DCV Input Resistance Test
5-3
6-1.
Reference Designation Index
6-2
5-4.
DCA Accuracy Test
5-3
6-2.
Replaceable Parts
6-7
5-5.
DC Voltage Output Test
5-4
6-3.
Replaceable Hardware
6-10
01556-2 Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
111
Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
List of Illustrations Model 410C
LIST OF ILLUSTRATIONS
Number
Page
Number
Page
1-1.
The ch/2 Model 410C Electronic Voltmeter .
1-1
4-4. Simplified Schematic, DC Voltage
2-1.
The Combining Case
2-0
Measurements
4-4
2-2.
Steps to Place Instrument in Combining
4-5. Simplified Schematic, Resistance Mea-
Case
2-0
surement
4-5
2-3.
Adaptor Frame Instrument Combina-
4-6. Simplified Schematic, AC Voltage Mea-
tion
2-1
surement
4-6
2-4.
Two Half Modules in Rack Adaptor
2-2
5-1. Alternate Voltage Source
5-1
3-1.
Front and Rear Panel Controls
3-3
5-2. DC Ammeter Operation
5-3
3-2.
DC Voltage Measurements
3-5
5-3. High Frequency Response Test
5-5
3-3.
DC Current Measurements
3-6
5-4. Low Frequency Response Test
5-6
3-4.
AC Voltage Measurements
3-7
5-5. Troubleshooting Tree
5-9
3-5.
Maximum AC Voltage Chart for 11036A
5-6. A4 Chopper Assembly Installation
5-10
Probe
3-8
5-7. Power Supply Measurements
5-12
3-6.
Graph Used in Calculation of Pulse Volt-
5-8. Power Supply Schematic
5-13
age Readings
3-9
5-9. Typical Amplifier Waveforms
5-14
3-7.
Resistance Measurements
3-10
5-10. Amplifier Schematic
5-15
3-8.
DC Nano-Ampere Current Measurements .
3-11
5-11. Model 11036A AC Probe Exploded
5-16
4-1.
Block Diagram, Model 410C
4-0
5-12. Model 11036A Probe Schematic
5-16
4-2.
Modulator-Demodulator Mechanical
5-13. RANGE and FUNCTION Switching (Pic-
Analogy
4-0
torial)
5-17
4-3.
Simplified Schematic, DC Current
5-14. Input RANGE and FUNCTION Switching
Measurement
4-3
Schematic
5-18
I v
Approved For Release 2001/04/20 :
CIA-RDP70600584R000100280001-3
01556-2
Model Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
410C
01556-2 Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
Section I
Figure 1-1
The Model 410C Electronic Voltmeter
1-1
Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
Section I
Table 1-1
Table 1-1. Specifications
AC VOLTMETER: ($ Model 11036A A C Probe re-
quired).
DC VOLTMETER
Voltage Range: ?15 my to ?1500 v full scale in
15, 50, 150 sequence (11 ranges).
Accuracy: ?2% of full scale on any range.
Input Resistance: 100 megohms ?1% on 500 my
range and above. 10 megohms ?3% on 15 my,
50 my, and 150 my ranges.
DC AMMETER
Current Ranges: -?1. 5 ?a to ?150 ma full scale
in 1.5, 5, 15 sequence (11 ranges).
Accuracy: ?3% of full scale on any range.
Input Resistance: Decreasing from 9 k ohms on
1.5 ?a scale to approximately 0.3 ohms on the
150 ma scale.
Special Current Ranges: ?1.5, ?5, and ?15
nanoamps full scale may be measured on the 15,
50 and 150 millivolt ranges using the Voltmeter
Probe, with ?5% accuracy and 10 megohm input
resistance.
OHMMETER
Resistance Range: Resistance from 10 ohms to
10 megohms center scale (7 ranges).
Accuracy: Zero to midscale: ?5% of reading or
+2% of midscale, whichever is greater.
?7% from midscale to scale value of 2
?8% from scale value of 2 to 3
?9% from scale value of 3 to 5
?10% from scale value of 5 to 10
AMPLIFIER
Voltage Gain: 100 maximum
AC Rejection: 3 db at 1/2 cps; approximately 66
db at 50 cps and higher frequencies for signals
less than 1600 v peak or 30 times. full scale,
whichever is smaller.
Isolation:Impedance between common and chassis
is >10 megohms in parallel with O. 1 ?f. Common
may be floated up to 400 v dc above the chassis
for dc and resistance measurements
Output: Proportional to meter indication; 1.5 v
de at full scale: maximum current, 1 ma.
Output Impedance: Less than 3 ohms. at dc.
Noise: Less than 0.5% of full scale on any range
(13-13).
DC Zero D,rift: Less than 0.5% of full scale/year
at constant temperature. Less than 0.05% of full
scale/?C.
Overload Recovery: Recover from 100:1 overload
in < 3 seconds.
Model 410C
Ranges: 0.5 v full scale to 300 v in 0.5, 1.5, 5
sequence (7 ranges).
Accuracy: ?3% of full scale at 400 cps for
sinusoidial voltages from 0.5 volts to 300 volts.
The AC Probe responds to the positive peak-
above-average value of signal applied.The instru-
ment is calibrated in rms volts for sine-wave
inputs.
Frequency Response: ?2% at 100 mc; ?10%
from 20 cps to 700 mc ( 400 cps reference).
Indications to 3000 mc.
Frequency Range: 20 cps to 700 mc.
Input Impedance: Input capacity 1. 5 pf; input
resistance >10 megohms at low frequencies.
At high frequencies impedance drops off due
to dielectric loss.
Safety: The probe body is grounded to chassis
at all times for safety. All ac measurements
are referenced to chassis ground.
Meter: Individually calibrated taut band meter
responds to positive peak-above-average.
Calibrated in rms volts for sine wave input.
GENERAL
Maximum Input: DC: 100 v on 15, 50 and
150 my ranges: 500 v on O. 5 to 15 v ranges;
1600 v on higher ranges. AC: 100 times full
scale or 450 v peak, whichever is less.
Power: 115 or 230 v ?10%. 50 to 1000 cps,
13 watts (20 watts with 0-p) Model 11036A AC
Probe).
Dimensions: 6-17/32 in. ( 16.5 cm) high,
5-1/8 inches (13.01 cm) wide, 11 in. (27.9 cm)
deep behind panel.
Weight: Net 8 lbs (4.0 Kg); shipping approx.
14 lbs. (6.35 Kg).
Accessory Furnished: Detachable power cord.
NEMA plug; $-,) Model 11036A AC Probe.
Option 02: 9, Model 410C less AC Probe.
1-2 Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
01556-2
Model 416Pproved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3 Section I
Paragraphs 1-1 to 1-13
SECTION I
GENERAL INFORMATION
1-1. DESCRIPTION.
1-2. The Hewlett-Packard Model 41 OC Electronic
Voltmeter can be used to measure DC voltage and DC
current; AC voltage and resistance. Positive and
negative DC voltages from 10 millivolts to 1500 volts
and positive and negative DC currents from 1.5 micro-
amperes to 150 milliamperes can be measured full
scale. Resistance from 10 ohms to 10 megohms full
scale can be measured with an accuracy of ?5% of
reading at midscale; resistance from 0.2 ohms to 500
megohms can be measured with reduced accuracy.
The Model 410C Electronic Voltmeter is shown in
Figure 1-1; the specifications are given in Table 1-1.
1-3. With the Model 11036A detachable AC Probe,
the Voltmeter can be used to measure AC voltage from
20 cps to 700 Mc. From 20 cps to 100 Mc, AC voltage
from 0.5 to 300 volts can be measured; from 100 Mc
to 700 Mc, refer to Figure 3-5 for maximum AC vol-
tage that can be applied to the AC Probe. For additi-
onal information on the AC Probe, refer to Paragraph
1-8.
1-4. INSTRUMENT IDENTIFICATION.
1-5. Hewlett-Packard uses a two section, eight-digit
serial number (000-00000). The serial number is on
a plate attached to the rear panel of the instrument.
If the first three digits of the serial number on your
instrument do not agree with those on the title page
of this manual, Appendix C, Backdating Changes will
define differences between your instrument and the
Model 410C described in this manual.
1-6. ACCESSORIES AVAILABLE.
1-7. Accessories are available that extend the AC
and DC measuring capabilities of the Voltmeter. A
description of these accessories and their specifica-
tions is given below.
1-8. MODEL 11036A AC PROBE. This accessory,
when used with the Model 410C, permits AC voltage
measurements from 0.5 volts rms to 300 volts rms,
full scale over a frequency range of 20 cps to 700 Mc.
Reference calibration accuracy at 400 cps (sinusoidal)
is ?3% of full scale. Frequency response is ?10% from
20 cps to 700 Mc, with indications obtainable to 3000
Mc. Frequency response at 100 Mc is within ?2%.
The Model 11036A responds to the positive-peak-
above-average value of the signal applied. The Model
410C is calibrated to read in RMS volts, for sine wave
inputs.
1-9. MODEL 11039A CAPACITIVE VOLTAGE DIVI-
DER. This accessory (formerly the Model 452A)
extends the AC voltage range of the Model 410C to 25
kv. The divider permits measurements of extremely
high AC voltage such as encountered in dielectric
heating equipment, etc., over a frequency range of
25 cps to 20 Mc. A fixed gap is provided so that break-
down will occur if the applied voltage exceeds 28 kv at
low frequencies. Voltage division is 1000:1, ?3%, and
input capacity is 15 picofarads. A Model 11018A
Adapter is also required to connect the Model 11036A
AC Probe to the shielded banana plug fitting of the
divider.
1-10. MODEL 11040A CAPACITY DIVIDER. This
accessory (formerly the Model 453A) extends theAC
voltage range of the Voltmeter to 2000 volts RMS. The
divider is for use at frequencies above 10 kc. Voltage
division is 100:1, ?1%, and input capacity is approxi-
mately 2 picofarads.
1-11. MODEL 11042A PROBE T CONNECTOR. This
accessory (formerly the Model 455A) is used for con-
necting the Model 11036A Probe across a 50-ohm
transmission line using type N connectors. The T-
joint is such that connection of the probe into a trans -
mission line will not cause a standing wave ratio
greater than 1.1 at 500 Mc and 1.2 at 1000 Mc. With
this device, measurement of power traveling through
a transmission line may be made with reasonable ac-
curacy to 1000 Mc. The usual precautions must be
takento provide accurate impedance matching and the
elimination of standing waves along the line through
which power is floating. By using a dummy load at
the receiving end of this T-joint, power output of
various devices can be measured. In many applica-
tions power going into a real load, such as an antenna,
can be conveniently measured up to 1000 Mc with good
accuracy.
1-12. MODEL 11043A TYPE N CONNECTOR. This
accessory (formerly the Model 458A) allows the AC
Probe to be connected to a 50-ohm coaxial line. The
connector uses a male type N connector and a recep-
tacle for receiving the probe. Terminating resistor
is not included.
1-13. MODEL 11045A DC DIVIDER. This accessory
extends the maximum DC voltage range of the Model
410C to 30 kv. Voltage division is 100:1, ?5%, and
input resistance is 9900 megohms. When used with
the Mode1410C, input resistance is 10,000 megohms.
This probe offers maximum safety and convenience
for measuring high voltages such as in television
equipment, etc. The maximum current drain is 2.5
microamperes.
01556-2 Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
1-3
Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
Section IT
;A igures 2-1 and 2-2
STEP I
SLIDE TOP PART
TO LIMIT
STEP
SLIDE BOTTOM PART
TO LIMIT
STEP ?
PUSH IN TO LIMIT
STEP (4)
SLIDE OVER TO LIMIT
DIVIDER LATCH
i-..;tire 2-1. The Combining Case
/
fl1 I i
/ H
, ! H,
! 1/, =, ..,c- ..1 r
:0- )
kJ ,
STEP
PUSH DOWN
TO RELEASE
DIVIDER ASSEMBLY
SUBMODULE RETAINER
Model 410C
STEP
PLACE INSTRUMENT
INTO CASE
STEP 7
SET RETAINER BACK
INTO PLACE
STEP (ED
PUSH UP TO LOCK
igure 2-2. Steps to Place Instrument in Combining Case
2-0 Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
01556-1
Approved For Release 2001/04/20: CIA-RDP70600584R000100280001-3
Model 410C
SECTION II
INSTALLATION
2-1. INSPECTION.
2-2. This instrument was carefully inspected both
mechanically and electrically, before shipment. It
should be physically free of mars or scratches and in
perfect electrical order upon receipt. To confirm
this, the instrument should be inspected for physical
damage in transit. Also, check for supplied acces-
sories, and test the electrical performance of the in-
strument using the procedure outlined in Paragraph
5-5, Performance Checks. If there is damage or
deficiency, see the warranty on the inside rear cover
of this manual.
2-3. INSTALLATION.
2-4. The V Model 410C is transistorized except for
one vacuum tube and requires no special cooling.
However, the instrument should not b operatsd where
the ambient temperature exceeds 55 C (140 F).
2-5. RACK MOUNTING.
2-6. The Model 410C is a submodular unit designed
for bench use. However, when used in combination
with other submodular units, it can be bench and/or
rack mounted. The 0,0 Combining Cases and Adapter
Frame are designed specifically for this purpose.
2-7. MODELS 1051A AND 1052A COMBINING CASES.
The Combining Cases are full-module units which
accept various combinations of submodular units.
Being a full width unit, it can either be bench or rack
mounted. An illustration of the Combining Case is
shown in Figure 2-1. Instructions for installing the
Model 410C are shown in Figure 2-2.
2-8. RACK ADAPTER FRAME MI Part No. 5060-
0797). The adapter frame is a rack mounting frame
that accepts various combinations of submodular
units. It can be rack mounted only. An illustration
of the adapter frame is given in Figure 2-3. Instruc-
tions are given below.
a. Place the adapter frame on edge of bench as
shown in step 1, Figure 2-4.
b. Stack the submodular units in the frame as
shown in step 2, Figure 2-4. Place the spacer clamps
between instruments as shown in step 3, Figure 2-4.
c. Place spacer clamps on the two end instruments
(see step 4, Figure 2-4)and push the combination into
the frame.
d. Insert screws on either side of frame, and
tighten until submodular instruments are tight in the
frame.
e. The complete assembly is ready for rack
mounting.
Section II
Paragraphs 2-1 to 2-13
2-9. THREE-CONDUCTOR POWER CABLE.
2-10. To protect operating personnel, the National
Electrical Manufacturers' Association (NEMA) re-
commends that the instrument panel and cabinet be
grounded. All Hewlett-Packard instruments are
equipped with a three-conductor power cable which
grounds the instrument when plugged into an appropri-
ate receptacle.
2-11. To preserve the protection feature when oper-
ating the instrument from a two-contact outlet, use
three - prong to two - prong adapter and connect the
green pigtail on the adapter to ground.
2-12. PRIMARY POWER REQUIREMENTS.
2-13. The Model 410C can be operated from either
115 or 230 volts, 50 to 1000 cps. The instrument can
be easily converted from 115- to 230- volt operation.
The LINE VOLTAGE switch, S4 a two-position slide
switch located at the rear of the instrument, selects
the mode of AC operation. The line voltage from
which the instrument is set to operate appears on the
slider of the switch. A 0.25-ampere, slo-blo fuse is
used for both 115- and 230-volt operation.
FILLER PANEL
0
0
0
0
0
0
0
0
0
0
4100 -B-16 !
Figure 2-3. Adapter Frame Instrument Combination
o1556-2Approved For Release 2001/04/20 CIA-RDP70600584R000100280001-3
2-1
Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
Section II
Paragraph 2-14 to 2-15
DO NOT CHANGE THE SETTING OF THE
LINE VOLTAGE SWITCH WHEN THE VOLT-
METER IS OPERATING.
2-14. REPACKAGING FOR SHIPMENT.
2-15. The following paragraphs contain a general
guide for repackaging of the instrument for shipment.
Refer to Paragraph 2-16 if the original container is
to be used; 2-17 if it is not. If you have any questions,
contact your local 0 Sales and Service Office. (See
Appendix B for office locations.)
NOTE
If the instrument is to be shipped to Hewlett-
Packard for service or repair, attach a tag
to the instrument identifying the owner and
indicate the service or repair to be per-
formed; include the model number and full
serial number of the instrument. In any
correspondence, identify the instrument by
model number, serial number and serial
number prefix.
2-16. If the original container is to be useo,proceed as
follows:
a. Place instrument in original container if avai-
lable. If original container is not available, one can
be purchased from your nearest Sales Sales and Service
Office.
O. Ensure that container is well sealed with strong
tape or metal bands.
2-17. If original container is not to be used, proceed
is follows:
a. Wrap instrument in heavy paper or plastic
before placing in an inner container.
b. Place packing material around all sides of
instrument and protect panel face with cardboard
strips.
0
ADAPTER
FRAME
Model 410C
I/2 MODULE
INSTRUMENT
SPACER
CLAMP
Qts,
SPACER CLAMP
RETAINING SCREWS
Figure 2-4. Two Half Modules in Rack Adapter
c. Place instrument and inner container in a heavy
carton or wooden box and seal with strong tape or
metal bands.
d. Mark shipping container with "DELICATE
INSTRUMENT", "FRAGILE", etc.
-'-2 Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
015564
Approved For Release 2001/04/20: CIA-RDP70600584R000100280001-3
Model 410C Section III
Paragraphs 3-1 to 3-18
SECTION III
OPERATION
3-1. INTRODUCTION.
3-2. The Model 410C is used to measure AC and DC
voltage, DC current, and resistance. All measure-
ment inputs are located on the front panel; a DC out-
put connector is located on the rear panel. Front
panel controls and indicators are color coded. DC
voltage, DC current and resistance knobs and indi-
cators are in black; AC voltage controls and indica-
tors are in red.
3-3. ADJUSTMENT OF MECHANICAL ZERO.
3-4. The procedure for adjustment of mechanical
zero is given in Section V.
3-5. FRONT AND REAR PANEL DESCRIPTION.
3-6. Figure 3-1 describes the function of all front
and rear panel controls, connectors and indicators.
The description of each control, connector and indi-
cator is keyed to a drawing which accompanies the
figure.
.1?4 1416?' 3-7. OPERATING PROCEDURES.
3-8. There are five operating procedures: DC Volt-
age Measurements, Figure 3-2; DC Current Measure-
ments, Figure 3-3; AC Voltage Measurements, Fig-
ure 3-4; Resistance Measurements, Figure 3-7; and
Measuring DC Current in Nano-amperes, Figure 3-8.
Note
Ageing of the neon lamps in the chopper
assembly can cause a change in chopper
frequency which produces a slight osci-
llatory movement of meter pointer. If
this oscillatory movement is observed,
rotate Osc Freq Adj A3R5 (see Paragra-
graph 5-2 8) in the ccw direction until
oscillation of pointer stops.
3-9. DC VOLTAGE MEASUREMENTS (Figure 3-2).
3-10. The Model 410C is normally floating; however
a shorting bar can be connected at the DC AMPLIFIER
OUTPUT connector on the rear panel. When the instru-
ment is floating, the COM Lead should not be connected
to voltages greater than 400 volts.
:3-11. DC CURRENT MEASUREMENTS (Figure 3-3).
3-12. General instructions for the measurement of
DC current are the same as those given for DC volt-
age measurements, Paragraph 3-9.
3-13. AC VOLTAGE MEASUREMENTS (Figure 3-4).
ONE SIDE OF ALMOST ALL POWER
DISTRIBUTION SYSTEMS IS GROUNDED.
EXTREME CAUTION MUST BE USED IF
DIRECT MEASUREMENT OF POWER
LINE VOLTAGES IS ATTEMPTED. IF
THE GROUND CLIP LEADIS ACCIDEN-
TALLY CONNECTED TO THE UN-
GROUNDED SIDE OF THE LINE . SEVERE
DAMAGE TO THE 410C IS POSSIBLE
BECAUSE OF THE SHORT CIRCUIT
CREATED. POWER LINE VOLTAGES
CAN BE SAFELYMEASURED BY USING
THE PROBE TIP ONLY. CONTACTING
THE GROUNDED POWER CONDUCTOR
WILL GIVE A READING OF 0 VOLTS
WHILE CONTACTING THE UN-
GROUNDED LEAD WILL GIVE FULL
VOLTAGE READING.
3-14. Although the Model 410C indicates a full scale
AC range of 500 volts, the optional Model 11036A AC
Probe should not be connected to AC voltages in ex-
cess of 300 volts RMS. AC voltage referenced to a
DC voltage may be measured, but the AC Probe clip
(alligator type) must be connected to the ground (-1-..)
of the circuit under test.
WHEN MEASURING AC REFERENCED
TO DC, THE PEAK AC VOLTAGE PLUS
DC VOLTAGE CONNECTED TO THE
PROBE MUST NOT EXCEED 420 VOLTS.
3-15. PRECAUTIONS WHEN MEASURING AC VOLT-
AGE.
3-16. Special considerations must be kept in mind
when makingAC voltage measurements. These con-
siderations are discussed in the following paragraphs.
3-17. GENERAL CONSIDERATION OF COMPLEX
WAVEFORMS. Waveforms containing appreciable
harmonics or spurious voltages will introduce error
in the meter indication since the meter has been cali-
brated to read RMS values of true sine waves while
the Model 11036A Probe is a peak-above-average
responding device. The magnitude of error that may
be expected when harmonics are present on the mea-
sured waveform is indicated in Table 3-1.
3-18. VOLTAGE MEASUREMENTS AT FREQUEN-
CIES BELOW 50 CYCLES/SECOND. Voltage mea-
surements at frequencies as low as 10 cycles per
01556_#pproved For Release 2001/04/20: CIA-RDP70600584R000100280001-3 3-1
Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
Section III
Figure 3-1
-
VOLTS- AMPS
3
-,.._?-,?,
s
's ? IWI'llThr'74,-,,,' , f'5'X',,,,,'''' ? ,
OHMS
LECTIONIC
HEWLETT ()*.fl 5,
VO 1.111E III
_!5_510.5.1
AC ZERO RANGE
FUNCTION .3 MA
SELECTOR R.look
652eg 5V 15MA
ACV I.5V I /?*r.
DCV.--% 4 %?d#--- 4.. 72TI(551
51-DCV
[MUSA? B1.768.4 I5MA
?.150V
.I5V 1
.DCAP- , . . ' N.
px10.-..-\ '.g1SPO
-DCA .05V i __.-
IAC PROBE 1.5NA...2
I300V. MAX. .015V ?.1;g/Ot'
DCA
DCV COM OHMS c
_...
,
Model 410C
I
CD
()I-1Mo ODADJ,
e
DC AMPLIFIER OUTPUT
115V/230v/.25A SE,
\ 0
,,,--
0 0 0
'_a
..,,___________
NOT INCLUDED
WITH INSTRUMENT
1. FUNCTION SELECTOR: This control is used for
selecting type of measurement to be made. They
are: *DC Voltage, tDC Current, AC Voltage,
and resistance measurements.
2. AC ZERO: This control provides adjustment for
zero-setting the meter before making AC volt -
age measurements.
MECHANICAL ZERO ADJUST: This adjustment
mechanically zero-sets the meter prior to turn-
ing on Voltmeter.
4. RANGE: This control selects the full scale
meter range.
5. AC POWER SWITCH: This push bu:ton - lamp
combination, when depressed, turns the instru-
ment power on or off. The push button glows
when the Voltmeter power is on.
6. DCA-OHMS: This lead is used in conjunction
with the COM Lead to measure DC current or
ohms. The FUNCTION SELECTOR determines
which measurement is made.
7. COM: This lead is used with the input leads for
DC voltage current, AC voltage, and resistance
measurements. The COM Lead is normally
floating; however, a shorting bar can be con-
nected from the floating ground terminal to the
chassis ground terminal on the DC AMPLIFIER
OUTPUT connector. If a shorting bar is not
used, the COM Lead is floating except when the
FUNCTION SELECTOR is set to ACV.
8. DCV: This lead is used in conjunction with the
COM Lead to measure ?DC voltage.
9. AC PROBE (300V MAX): Receptacle for tele-
phone-type plug of Model 11036A AC Probe.
With probe connected the Voltmete:? may be
used to make AC voltage measurements.
10. coADJUST: This control is used to et meter
pointer to co before resistance measurements
are made. Only periodic adjustment of this
screwdriver adjustment is necessary.
11. LINE VOLTAGE: This two-position slide switch
sets the instrument to accept either 115 or 230
volt AC primary power.
12. FUSEHOLDER: The fuseholder contains a 0.25
ampere slow-blow fuse for both 115 vac and
230 vac modes of operation.
13. AC POWER CONNECTOR:Accepts power cable
supplied with the instrument.
14. DC AMPLIFIER OUTPUT: Provides DC vol-
tage output proportional to meter indication for
driving external recorder. 1.5 volts DC out-
put for full scale meter deflection.
Figure 3-1. Front and Rear Panel Controls
3-2 Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
01556-2
Approved For Release 2001/04/20: CIA-RDP70600584R000100280001-3
Model 410C
second may be made without loss of accuracy by re-
moving the plastic nose on the Model 11036A and using
in its place a 0.25 microfarad blocking capacitor in
Niro, series with the exposed contact of the probe.
\No"
THE GRAY INSULATING MATERIAL
AROUND THE AC PROBE IS POLY-
STYRENE, A LOW-MELTING POINT
MATERIAL. IT IS NOT POSSIBLE TO
SOLDER TO THE CONTACT WHICH IS
EXPOSED WITH THE PROBE NOSE IS
REMOVED WITHOUT DESTROYING
THE POLYSTYRENE.
Table 3-1. Possible Error When Measuring Voltage
of Complex Waveforms
To Harmonic
True RMS Value
Voltmeter Indication
0
100
100
10%
2nd
100.5
90 to 110
20%
2nd
102
80 to 120
50%
2nd
112
75 to 150
10%
3rd
100.5
90 to 110
20%
3rd
102
87 to 120
50%
3rd
112
108 to 150
3-19. VOLTAGE MEASUREMENT AT HIGH FRE-
QUENCIES. At frequencies above 100 megacycles
the distance between the point of voltage measure-
ment and anode of the probe diode must be made as
short as possible. If feasible, substitute a small disc
type capacitor of approximately 50 picofarads for the
removable tip on the probe. Solder one terminal of
the button capacitor to the measurement point in the
circuit and not to the probe contact. The probe con-
tact ( with tip removed ) can then contact the other
terminal of the capacitor for the measurement.
3-20. At frequencies above 100 megacycles consid-
erable voltage may be built up across ground leads
and along various part of a grounding plane. Con-
sequently, to avoid erroneous readings when measur-
ing medium and high frequency circuits, use the
ground clip lead on the shell of the probe to connect
the circuit ground. In some cases at the higher fre-
quencies it maybe necessary to shorten the grounding
lead on the probe.
3-21. For all measurements at higher frequencies,
hold the molded nose of the probe as far from the ex-
ternal ground plane or from object at ground potential
as can conveniently be done. Under typical conditions,
this practice will keep the input capacitance several
tenths of a picofarad lower than otherwise.
3-22. For measurements above approximately 250
megacycles it is almost mandatory that measurements
be made on voltages which are confined to coaxial
transmission line circuits. For applications of this
type, the Model 11036A Probe is particularly suitable
because the physical configuration of the diode and
?*tmilso' probe is that of a concentric line, and with a few pre-
cautions it can be connected to typical coaxial trans-
mission line circuits with little difficulty.
Section In
Paragraphs 3-19 to 3-27 and Table 3-1
3-23. To connect the probe into an existing coaxial
transmission line, cut the line away so the center con-
ductor of the line is exposed through a hole large
enough to clear the body of the probe. The nose of the
probe should be removed for this type of measurement.
Connect one terminal of a button-type capacitor of ap-
proximately 50 picofarads to the center conductor of
the coaxial line so that the other terminal of the capa-
citor will contact the anode connection of the probe.
A close-fitting metal shield or bushing should be ar-
ranged to ground the outer cylinder of the probe to the
outer conductor of the transmission line. This type of
connection is likely to cause some increase in the
standing wave ratio of the line at higher frequencies.
The Model 11042A Probe T Connector is designed to
do this job with SWR or less than 1.1 at 500 Mc (see
Paragraph 1-11).
3-24. EFFECT OF PARASITICS ON VOLTAGE
READINGS. At frequencies above 500 megacycles,
leads or portions of circuits often resonate at fre-
quencies two, three, or four times the fundamental
of the voltage being measured. These harmonics may
cause serious errors in the meter reading. Owning to
the resonant rise in the probe circuit at frequencies
above 1000 megacycles, the meter may be more sen-
sitive to the harmonics than to the fundamental. To
make dependable measurements at these frequencies,
the circuits being measured must be free of all para-
sitics.
3-25. EFFECT OF DC PRESENT WITH AC SIGNAL.
When measuring an AC signal at a point where there
is a high DC potential, such as at the plate of a vacuum
tube, the high DC potential may cause small leakage
current through the blocking capacitor in the tip of the
Model 11036A AC Probe. When the AC signal under
measurement is small, the error introduced into the
reading can be significant. To avoid leakage, an addi-
tional capacitor with a dielectric such as mylar or
polystyrene which has high resistance to leakage is
required. (Use 5 picofarads or higher, and insert the
capacitor between the point of measurement and the
probe tin. 1
3-26. PULSE MEASUREMENTS.
3-27. POSITIVE PULSES.The Mode111036A AC Probe
is peak-above- average responding and clamps the
positive peak value of the applied voltage. This per-
mits the probe to be used to measure the positive-
voltage amplitude of a pulse, provided the reading ob-
tained is multiplied by a factor determined from the
following expression:
1.4
+ K
1 + tl
t2
(
PRF
t1 is the duration of the positive portion of the
voltage in microseconds.
is the duration of the negative portion of the
voltage in microseconds.
K is a factor determined from the expression
R0/t1 and the graph shown as Figure 3-6,
where Ro is the source impedance of the pulse
generator in kilohms, and t1 is the duration of
the positive portion of the pulse in micro-
seconds.
t2
01556hpproved For Release 2001/04/20 CIA-RDP70600584R000100280001-3 3-3
Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
:=;ection III
Paragraphs 3-28 to 3-34
PRF is the pulse repetition frequency in pulses per
second (pps).
Suppose, for example:
t 10 microseconds
t2 - 990 microseconds
K = 0.55
= 1000 pps
To find K, assuming R0 = 2 kilohms and t1= 10 micro-
seconds: R0/4 = 2/10? = 0.2. Location0.2 onthe
X axis of the graph shown as Figure 3-6, and reading
K where X and Y axes intersect the unmarked curve. If
the ratio of R0/t1 were greater than 1, multiply the
X and Y axes by 10, and use the curve marked "R0/
' and K each X10".
1
Solving the expression for the multiplying factor,
3-4
(10 0.55)
1. 4 1 4
990 1000
1.4 (1 + 0.01 + 0.00055)
1.4 (1.01055)
1.41477
3-28. NEGATIVE PULSES.
Model 410C
3-29. In the case of a 10 microsecond negative pulse
(t2) and a pulse repetition frequency (PRF) of 1000 pps,
it would be 990 microseconds. Thus T?/ti would be
approximately 0, and from the graph it is seen that
K is approximately 0. The expression would then
reduce to
990
4 ( 1 + )
3-30. It can be seen that in the case of negative pulses
of short duration much smaller readings will be ob-
tained for an equivalent positive pulse. As a result,
large multiplying factors must be used and unless the
pulse voltage is large, these measurements may be
impractical.
3-31. MEASURING RESISTANCE (Figure 3-7).
3-32. Before making resistance measurements,power
must be removed from the circuit to be tested. Also,
make sure capacitors are discharged to eliminate any
residual voltage.
3-33. MEASURING DC NANO-AMPERE CURRENT
(Figure 3-8).
3-34. The Model 410C can be used to measure nano-
ampere leakage current in transistors and diodes. The
three most sensitive DC voltage measurement ranges
are used to measure DC nano-ampere currents.
Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
01556-2
Approved For Release 2001/04/20: CIA-RDP70600584R000100280001-3
Model 410C
Section III
Figure 3-2
?
VOLTS - AMPS
5 3
1. .4
to
o ,t
o
o I
1, OHMS
LECTRONIC % % LW
NEVILET*PACKARD
OLIMMR MODEI.
I
AC ZERO RANGE
FUNCTION _,A MA
SELECTOR
IFFP4 a ptAylook
mg'
ACV 1,5V "-N ,---,,v
-DCV*--, ' 501 M
R ?M
+DCV .5V ''''', ..--'175;VA
OHM50?
+DCA ?, Rliftato? i1/40 Irg
RMOV er . . . 50MA
500V
-DCAA?, .05V /
1 WA 15 0MA
( 30C4.R411%. ) :015V"-j 1500V
0 r0 C._ ,V COM &CA
f
1. Depress the AC power switch (neon- switch
combination).
Set FUNCTIONSELECTOR to polaritydesired
(+DCV or -DCV).
? Set RANGE to desired voltage position.
? Connect COM Lead to the ground of circuit
under test. Do not connect common lead to
voltages greater than 400 volt when making
off-cabinet-ground connections.
WARNING
WHEN MEASURING POTENTIALS
REFERENCED TO VALUES OFF
GROUND, REMOVE SHORTING
STRAP FROM DC AMPLIFIER
OUTPUT CONNECTOR ON REAR
PANEL. IF THE SHORTING STRAP
IS NOT REMOVED, THE INSTRU-
MENT CABINET IS TIED TO THE
ID
OHMS ADJ,
DC AMPLIFIER OUTPUT
II5V/230V/.. 25A SO
?o
IlL2
NOT INCLUDED
WITH INSTRUMENT
410C-13-18
COMMON LEAD. NORMALLY, FOR
SAFETY, THE CABINET IS ALSO
TIED TO EARTH GROUND
THROUGH THE THIRD WIRE TO
THE THREE-PRONG CONNECTOR.
IF THIS THIRD WIRE CONNECTION
WERE REMOVED (BY USING AN
ADAPTING PLUG) THE CABINET
WILL ASSUME AN ELEVATED PO-
TENTIAL.
5. Touch DCV probe to test point.
6. Read voltage on the VOLTS-AMPS scale.
Note
Ageing of the neon lamps in the
chopper assembly can cause a change
in chopper frequency which pro-
duces a low amplitude oscillatory
movement of the meter pointer. If
the meter pointer oscillates, rotate
A3R5 ccw until oscillation stops.
Figure 3-2. DC Voltage Measurements
Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
01556-2
3-5
Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
Section III
Figure 3-3
VOLTS-AMPS
, ,1,_,,_d ?lc,.
to I
4.0
s OHMS
% ., 4, es sC. SY IC 041V
ELECTRONIC .. HEIELE11#PNCNARD 4,,.., 15..43
VaLTNIETEI ROHL 41
AC ZERO RANGE
FUNCTION .3 MA /
SELECTOR 150 A ROE
I.5MA
ACV 11.C515.-\ 1 l'5VM
-13CV72.- - VOL M
INOC?-7 50V
O V
HMS 468? rTh --::n
.I5V
*DCA .4,
a ..50MA
-
-DCA _ .05V , -S, 500V
AC PROBE I sUA/ o__
13005. MAX.) :ow/ \-.1INV
DCA
DCV COM OHMS j.
-.4.
k
Depress the AC power switch (neon-switch com-
bination).
Set FUNCTION SELECTOR to the polarity de-
sired (+DCA or -DCA).
3. Set range to desired current position.
3-6
Connect COM Lead to the ground of circuit under
test. Do not connect common lead to voltages
greater than 400 volts, when making off-cabinet
ground connections.
WARNING
IF THE SHORTING STRAP IS NOT
REMOVED, THE INSTRUMENT
CABINET IS TIED TO THE COM-
,C)
Model 410C
M.-MILIEZ-2..._
(1)
OHMS ADJ.
a"
DC AMPLIFIER OUTPUT
35V/230V/.25ASB
0 C)
03,M0.11 \
\m-
0 6, 0
I if
,
NOT ,NCLUDED
W'TH INSTRUMENT
MON LEAD. NORMALLY FOR
SAFETY, THE CABINET IS ALSO
TIED TO EARTH GROUND THROUGH
THE THIRD WIRE TO THE THREE-
PRONG CONNECTOR. IF THIS
THIRD WIRE CONNECTION WERE
REMOVED (USING A TWO PRONG-
TO-THREE PRONG ADAPTER),
THE CABINET WILL BE AT AN
ELEVATED POTENTIAL.
5. Connect the DCA ohms probe to the circuit to be
tested.
6. Read the current on the VOLTS-AMPS scale. IAft
Figure 3-3. DC Current Measurements
Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
01556-3
Approved For Release 2001/04/20: CIA-RDP70600584R000100280001-3
Model 410C
Section III
Model 410C
)-.....
-
,-...,
VOLTS - AMPS
2
? O .3 10 1
.1
7.0
0 \ 1
a $
I2 OHMS 1 e
S
ELECTIONIC s IWLE1TPCURU 4 % 1.5 OMIT
VOLTAM(' NOM MOO
+DCV
OHM
1 3A000
s)
-DCA?--,
741 ,
AC ZERO
FUNCTION
SELECTOR
ACV
DCV
r.--
RANGE
.5 MA
WillP RMOON
5V L 5MA
I.5V VI
50V
Rit +? Int
Rx10
.05V
ISLE ISOMA
.0I5V (5000
COM
...--
CONNECT AC PROBE CLIP TO EARTH GROUND ONLY.
1. Connect the Model 11036A AC Probe to the
Model 410C at the AC PROBE receptacle.
2. Set FUNCTION SELECTOR to ACV. NOTE:
COM and chassis are internally connected when
the FUNCTION SELECTOR is set to ACV.
3. Set RANGE to . 5V.
4. Depress the AC power button (neon-switch com-
bination) and allow 5 minute warmup.
5. Adjust AC ZERO for a zero indication on the
meter.
6. Set RANGE to the desired voltage range.
7. Connect AC Probe clip (alligator) io ground of
circuit to be tested, and touch probe tip to test
point. At lower frequencies COM Lead can be
substituted for the AC probe clip.
BEFORE MEASURING VOLTAGES AT FRE-
QUENCIES ABOVE 100 MC, REFER TO
FIGURE 3-5, TO DETERMINE THE MAXI-
MUM AMOUNT OF VOLTAGE THAT CAN BE
APPLIED AT THAT FREQUENCY.
8. Read AC voltage on the VOLTS -AMPS scale.
NOTE: When RANGE is on the . 5V and 1.5V
positions, use red meter scale.
Figure 3-4. AC Voltage Measurements
01556-Approved For Release 2001/04/20 CIA-RDP70600584R000100280001-3
3-7
Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
Section In
Figure 3-5
3-B
Model 410C
Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
Figure 3-5.
01556-2
Model Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
Section III
Figure 3-6
Figure 3-6. Graph Used in Calculation of Pulse Voltage Readings
01556-2
Approved For Release 2001/04/20 : CIA-RDP701300584R000100280001-3
3-9
Approved For Release 2001/04/20: CIA-RDP70600584R000100280001-3
Section III
Figure 3-7
VOLTS - AMPS
,7?.,,..?< 0/
1. /,'?,),..,x,
to
? ? 5' 1
ta 4'4Vi,:r =Orr
LECTIONIC % IIEVEIT#PACIIIRD
litillEIFI 111111FL 410C
AC ZERO
0 RANGE
FUNCTION .o MA
SELECTOR Rx100K
Inif.t?, 5V I.5MA
?-???RxIM
Spy I.5V / IDV
?
. -..\
OHM.0S.CV.- R. at In
,,,,%5
R5 ,. 500V
-DCA.L', ------ 4illt
AC PROBE
(300V. MA .) .0I5V .1500V
DCA
DCV COM OHMS .0.
.... ..-- -I O
Iodel 410C
a)
OHMS ADJ.
DC AMPLIFIER OUTPUT
H5V/230V/ 25A SB
OS'e.
.....-...,
in
_
Before making resistance measurements, remove
power from circuit to be tested. Be sure to dis-
charge capacitors to eliminate any residual voltage.
3-10
Depress AC power switch (neon-switch combina-
tion).
Set the FUNCTION SELECTOR to OHMS.
Set RANGE to desired position.
410,-9-16
4. Adjust OHMS 00ADJ. control on rear panel to
obtain an co reading on the meter if necessary.
5. Connect COM and DCA OHMS leads across cir-
cuit to component to be tested.
6. Resistance is determined by multiplying the
reading on the OHMS scale by the RANGE factor.
EXAMPLE: If reading is 1.5 and factor is 10K,
then resistance equals 15K ohms.
1.1fe 3-7 Resistance Measurements
Approved For Release 2001/04/20 : CIA-RDP701300584R000100280001-3
01556-2
Model inkroved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
Section III
Figure 3-8
VOLTS - AMPS
3
10
$ 1 .1
?,
..r.
L OHMS
o ?.SnIDELY
ELECTRONIC TT, 4, % I EDDY L
HEWLETT PACK 11
VOLTMETER MODEL 1100
AC ZERO
FUNCTION
SELECTOR
Ar
-DCVW'
+DCV
OHMs.?
? ?
-DCA.--0 -
AC PROBE
1300V. MAX.)
I--..
0 DCV
RANGE
.5 MA
R.100K
5V
01,.5L\ /Hai,
SOA V I dv
10 HI
.5V 50V
RMg - r5n
.15V
-..,
RV .) Er
.05V
5005
1.. 015V 150MA
1500V
DCA
COM
'-- \ OHMS
...^ x `i
RC)
I. Set the FUNCTION SELECTORto+DCV or -DCV
(depending on direction of current flow).
2. Set RANGE to desired range (.015V, . 05V, or
. 15V range).
Note
0.015V range = 1. 5 nano-amperes range
0..05V range = 5. 0 nano-amperes range
0. 15V range = 15 nano-amperes range
3. Connect the DCV lead to the circuit under test.
4. Connect the COM lead to the circuit under test.
5. Read nano - amperes from the meter on the
VOLTS-AMPS scale (top two on meter) which
corresponds to the range selected.
Figure 3-8. DC Nano-Anmere Current Measurements
01556-lekpproved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
3-11
Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
Section IV
Figure 4-1 and 4-2
AC ZERO
INPUT
LEADS
0
rOHMS ooAD..7.1
AIRE Q Q R3
P/O 44
P/O 43
P/O 44
P/043
AC
CATHODE
AMPLIFIER
DEMODULATOR
V3 a V4
FOLLOWER
VIA,01, a Q2
VIB
A '7
AISI bA2S2
FUNCTION \
SELECTOR \
NOTES:
P/O. PART OF.
4-0
RANGE
SELECTED
FEEDBACK
NETWORK
Model 410C
DC AMPLIFIERI MI
OUTPUT
2
Figure 4-1. Block Diagram, Model 410C
180 PHASE
-.75V?FT:W +I2V?E?Flw -
+
MODULATOR P/O A4
SELECTED
INPUT
NETWORK I5MV
AISI a 42S2 DC A3C.4
4
0
42832
20
A2R33
10
43821
10K
43825
2200
/77
PLO AISID(R)
0
'934/
0
0
0
0
0
0
P/0 AISIC(P)
0 0
> 4>-a. -9V
MI
250
A6817
180
DC
0
0
46820
DC OUTPUT
ADJ
46818 A6R21
970
300
e
\935,
'9371
A6C81
A6R16
8200
0
1-DCA 1
1 + C A
OHMS'
1+Dcvi
1,-DCV 1
Figure 5-10. Amplifier Schematic
5-15
C-1?0008Z001?000t117890080/dCIU-VIO : OZ/P0/1.00Z eseelet1 JOd PeA0AdV
Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
Section V
Figures 5-11 and 5-12
Model 41(
BOOT
11036-42101
TUBE SOCKET a CABLE ASSEMBLY
11036 -62101
1920-0010
RETAINER RING
SPRING
J460-0087
CONTACT
4106-2,-1
GROUNDING CLIP
41013-21H
SLEEVE
41013-
PROBE CONTACT ASSEMBLY
0106-2 IC
BOOT
11036-42102
PROBE HEAD
4105-210
TELEPHONE PLUG
11039A-B-01136 1251-0209
AC GROUNDING JUMPER
410B-21J
/170/1?00Z eseeieu -10d peAoiddv
Figure 5-11. Model 11036A AC Probe (Exploded View)
0
-0
0
48 MODEL 110364 AC PROBE ASSEMBLY
r?
I A8C1
I 2600PF
INPUT
48 RI
22M
A8P1
tri
co
AC PROBE
(300V MAX)
J1
AIS1A R(10)
GROUNDING JUMPER
4/00-B-oi89
CO
TO AISID F(4)
TO AIS1D F(101)
2
NOTES
1. Unless otherwise specified, resistance in ohms.
Capacitance in microfarads.
2 value Of A8C2 includes probe lead capacity.
3. indicates an assembly. All components
located on any assembly are prefixed by the assembly
designation (e.g. R1 on assembly AS becomes A8R1).
Figure 5-12. Model 11036A AC Probe Schematic
5-16 01556-:
Model 41uuApproved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3 Section VI
Paragraphs 6-1 to 6-7
SECTION VI
REPLACEABLE PARTS
6-1. INTRODUCTION.
6-2. This section contains information for ordering
replacement parts. Table 6-1 lists parts in alpha -
numerical order of their reference designators and
indicates the description and $ stock number of each
part, together with any applicable notes. Table 6-2
lists parts in alpha-numerical order of their stock
number and provides the following information on
each part:
a. Description of the part (see list of abbreviations
below).
b. Typical manufacturer of the part in a five-digit
code (see list of manufacturers in Appendix).
c. Manufacturer's part number.
d. Total quantity used in the instrument (TQ col-
umn).
A = assembly
B = motor
C = capacitor
CR = diode
DL = delay line
DS = device signaling (lamp)
E = misc electronic part
a = amperes
bp = bandpass
bwo = backward wave
oscillator
C = carbon
cer = ceramic
cmo = cabinet mount only
coef = coefficient
COM = common
comp = composition
conn = connection
crt - cathode-ray tube
del) = deposited
EIA Tubes or transistors
meeting Electronic
Industries' Associa-
tion standards will
normally result in
instrument operating
within specifications;
tubes and transistors
selected for best
performance will be
supplied if ordered
by stock numbers.
REFERENCE
6-3. Replaceable hardware parts, not listed in Table
6-1 or 6-2, are listed in Table 6-3 in alphabetical
order of description.
6-4. ORDERING INFORMATION.
6-5. To obtain replacement parts, address order or
inquiry to your local Hewlett-Packard Field Office
(see lists at rear of this manual for addresses). Iden-
tify parts by their Hewlett-Packard stock numbers.
6-6. NON-LISTED PARTS.
6-7. To obtain a part that is not listed, include:
a. Instrument model number.
b. Instrument serial number.
c. Description of the part.
d. Function and location of the part.
DESIGNATORS
F =fuse
FL = filter
J =jack
K = relay
L = inductor
M = meter
MP = mechanical part
elect = electrolytic
encap= encapsulated
fxd
Ge
grd
Hg
= farads
= fixed
germanium
= ground (ed)
- henries
= mercury
impg = impregnated
inert = incandescent
ins = insulation (ed)
K - kilo = 1000
Tin
log
RT
= plug
= transistor
= resistor
= thermistor
= switch
= transformer
ABBREVIATIONS
mtg
my
= linear taper
logarithmic taper
m = milli = 10-3
M = megohms
ma = milliamperee
= micro = 10
minat = miniature
mfgl metal film on glass
mfr manufacturer
NC
No
NO
NPO
nsr
obd
pc
Pf
pp
piv
pos
poly
pot
rect
= mounting
= mylar
= normally closed
= neon
= normally open
= negative positive
zero (zero temp-
ature coefficient)
= not separately
replaceable
= order by de-
scription
peak
printed circuit
board
picofarads
10-12 farads
peak to peak
= peak inverse
voltage
= position (s)
= polystyrene
= potentiometer
= rectifier
V = vacuum tube, neon
bulb, photocell, etc.
= cable
X = socket
XF = fuseholder
XDS = lampholder
= network
rot = rotary
rms = root-mean-square
rmo = rack mount only
s-b = slow-blow
Se = selenium
sect = section(s)
Si = silicon
sil = silver
sl = slide
td = time delay
TiO2 = titanium dioxide
tog = toggle
tel = tolerance
trim = trimmer
twt = traveling wave tube
var = variable
w/ = with
= watts
ww = wirewound
w/o = without
= optimum value
selected at factory,
average value
shown (part may
be omitted)
01556-3 Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
6-1
Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
Section?vi
Table 6-1
'Fable 6-1 Reference Designation Index
Model 410C
REFERENCE
DESIGNATION
PART NO.
DESCRIPTION
NOTE
A1S1
410C-19B
Switch ass'y - selector, includes:
R1, 2 R10
R5 thru 7 Si
A1R1
0727-0004
R: fxd, dep c flm, 5 ohms ?l%, 1 /2 w
A1R2
0727-0480
R: fxd, carbon urn, 2.32 megohms ?1%, 0.5 w
A1R3 and
Not Assigned
Al R4
AlR5
0687-5661
R. fxd, comp, 56 megohms ?10%, 1/2 w
A1R6
2100-0389
R- var, ww, Lin taper, 10 K ohms ?10%, 5 w
A1R7
0687-1531
R. fxd, comp, 15K ohms ?10%, 1/2w
A1R8 and
Not Assigned
Al R9
A1R10
0727-0479
R: fxd, carbon flm, 250 ohms +1%, 1/2 w
A2S2
410C-19A
Switch as,s'y - range, includes:
R1 thru 4 R30 thru 33
R6, 7 S2
R10 thru 26
A2R1
0728-0004
R: fxd, carbon flm, 1 ohm ?1%, 1/2 w
A2R2
0727-0955
R: fad, carbon flm, 10.5 ohms ?1%, 1/2w
A2Ft3
0728-0004
R: fad, carbon flm, 1 ohm ?1%, 1/2 w
A2R4
0733-0018
R: fxd, carbon flm, 89 megohms +1%, 2 w
A2R5
Not Assigned
A2R6
0687-1031
R: fxd, comp, 10 K ohms ?10%, 1/2 w
A2R7
072'7-0478
R: fxd, carbon flm, 2.21 megohms ?1%, 1/2 w
A2R8 and
Not Assigned
A2R9
A2R10
0730-0176
R: fxd, 6 megohms +0.5%, 1 w
A2R11
0727-0459
R: lad, carbon flm, 2 megohms +0.5%, 1 w
A2R12
0727-0458
R: fxd, carbon flm, 700 K ohms +0.5%, 1/2 w
A2R13
0727-0457
R: fxd, carbon flm, 200 K ohms ?1%, 1/2 w
A2R14
0727-0456
R: fxd, carbon flm, 70 K ohms ?0.5%, 1/2 w
A2R15
0727-0455
R: fxd, carbon flm, 20 K ohms +0.5%, 1/2 w
A2R16
0727-0451
R: fxd, carbon flm, 1 K ohm +0.5%, 1/2 w
A2R17
0727-0454
R: fxd, carbon urn, 6 K ohms ?0.5%, 1/2 w
A2R18
0727-0453
R: fxd, carbon flm, 2 K ohms +0.5%, 1/2 w
A2R19
0727-0452
R: fxd, carbon flm, 700 ohms ?0.5%, 1/2 w
A2R20
0727-0450
R: fxd, carbon urn, 200 ohms +0.5%, 1/2 w
A2R21
0727-0449
R: fxd, carbon flm,70 ohms ?1%, 1/2 w
A2R22
0727-0448
R: fad, carbon flm, 20 ohms +1%, 1/2 w
A2R23
0727-0446
R: fad, carbon urn, 7 ohms ?1%, 1/2 w
A2R24
0727-0445
R: fad, carbon flm, 2 ohms +1%, 1/2 w
A2R25
410C-26B
R: fad, 0.7 ohms
A2R26
410C-26A
R: fad, 0.3 ohms
A2R27 thru
Not Assigned
A2R29
A2R30
0727-0701
R: fad, carbon flm, 845 ohms ?1%, 1/2 w
A2R31
0727-0031
R: fxd, carbon flm, 60 ohms ?1%, 1/2 w
A2R32
0727-0448
R: fxd, carbon flm, 20 ohms ?1%, 1/2 w
A21?,33
0727-0948
R: fad, carbon flm, 10 ohms ?.1%, 1/2 w
A2R34
0687-1011
R: tad, comp, 100 ohms +10%, 1/2 w
: See introduction to this section
6-2 Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
01566-3
Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
Model 410C
Table 6-1. Reference Designation Index (Cont'd)
Section VI
Table 6-1
REFERENCE
DESIGNATION
* PART NO.
DESCRIPTION
NOTE
A3
410C-65A
Board ass'y - amplifier, includes:
C1, 2 R1 thru 3
C4 thru 6 R5
CB, 9 R7 thru 9
C11 thru 14 R12 thru 15
C16 R18 thru 21
CR1, 2 R24 thru 26
Qi, 2 R30, 31
V1
A3C1
0170-0030
C: fxd, poly, 0.1 IA ?10%, 50 vdcw
A3C2
0170-0077
C: fxd, poly, 0.047 tif ?10%, 50 vdcw
A3C3
Not Assigned
A3C4
0160-0161
C: fxd, my, 0.01 lif, 200 vdcw
A3C5
0140-0208
C: fxd, mica, 680 pf ?5%, 300 vdcw
A3C6
0160-0209
C: fxd, my, 0.33 p.f ?20%, 200 vdcw
A3C7
Not Assigned
A3C8
0180-0039
C: fxd, elect, 100 ?f, 12 vdcw
A3C9
0160-0200
C: fxd, my, 0.22 pi ?20%, 200 vdcw
A3C10
Not Assigned
A3C11
0180-0094
C: fxd, elect, 100 0, 25 vdcw
A3C12
0160-0200
C: fxd, my, 0.22 pi ?20%, 200 vdcw
A3C13
0150-0096
C: fxd, cer, 0.05 p,f, 100 vdcw
A3C14
0170-0018
C: fxd, my, 1 ptf ?5%, 200 vdcw
A3C15
Not Assigned
A3C16
0140-0154
C: fxd, mica, 1300 pf ?5%, 500 vdcw
A3CR1 and
1901-0156
Diode: si, 50 ma
A3CR2
A3R1
0687-6841
R: fxd, comp, 680 K ohms ?10%, 1/2 w
A3R2
0687-1851
R: fxd, comp, 1.8 megohms ?10%, 1/2w
A3R3
0811-0998
R: fxd, comp, 100 ohms ?1%, 1/4 w
A3R4
Not Assigned
A3R5
2100-0442
R: var, comp, lin taper, 40 K ohms ?30%, 1/4 w
A3R6
Not Assigned
A3R7
0687-5661
R: fxd, comp, 56 megohms ?10%, 1/2 w
A3R8
0687-4731
R: fxd, comp 47 K ohms ?10%, 1/2 w
A3R9
0687-4701
R: fxd, comp, 47 ohms ?10%, 1/2 w
A3R10 and
Not Assigned
A3R11
A3R12
0757-0164
R: fxd, met flm, 5.6 K ohms ?2%, 1/2w
A3R13
0757-0166
R: fxd, met flm, 30 K ohms ?2%, 1/2 w
A3R14
0757-0163
R: fxd, met flm, 3 K ohms ?2%, 1/2 w
A3R15
0757-0165
R: fxd, met flm, 13 K ohms ?2%, 1/2 w
A3R16 and
Not Assigned
A3R17
A3R18
0757-0091
R: fxd, met flm, 18 K ohms ?2%, 1/2 w
A3R19
0757-0166
R: fxd, met flm, 30 K ohms ?2%, 1/2 w
A3R20
0687-1021
R: fxd, comp, 1 K ohm ?10%, 1/2 w
A3R21
2100-0396
R: var, ww, lin taper, 10 K ohms ?20%, 1 w
A3R22 and
Not Assigned
A3 R23
# See introduction to this section
01566-3 Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
6-3
Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
Section VI
Table 6-1
Table 6-t. Reference Designation Index (Cont'd)
Model 410C
REFERENCE
DESIGNATION
(0,-e PART NO.
DESCRIPTION
NOTE
, A3R24
0687-2751
R: fxd, comp, 2.7 megohms ?10%, 1/2 w
A3R25
0687-2221
R: fxd, comp 2.2 K ohms ?10%, 1/2 w
A3R26
0687-1021
R: fxd, comp, 1 K ohm ?10%, 1/2 w
A3R27 thru
Not Assigned
A3 R29
A3R30
2100-0413
R: var, comp, lin taper, 2.5 megohms ?20%, 1/4 w
A3R31
2100-0227
R: var, ww, lin taper, 20 ohms ?10%, 1 w
A3Q1
1850-0013
Transistor: germanium, PNP
A3Q2
1850-0040
Tranasistor: germanimum, PNP
A3V1
1932-0027
Tube: electron, dual triode, 12AT7
A4
1990-0020
Ass'yr - chopper block, includes:
A4C1 A4R1, 2
A4DS1, 2 A5V1 thru 4
A4C1
Not separately replaceable, part of chopper ass'y
(1990-0020)
A4DS1 and
Not separately replaceable, part of chopper ass'y
A4DS2
(1990-0020)
A4R1 and
Not separately replaceable, part of chopper ass'y
A4R2
(1990-0020)
A4V1 thru
Not separately replaceable, part of chopper ass'y
A4V2
(1990-0020)
A6
41.0C-65B
Board ass'y - calibration, includes:
CR1 R14
Ftl R16 thru 18
R3 thru 8 R20, 21
A6CR1
1901-0025
Diode: si, 50 ma
A6R1
0727-0751
R: fxd, carbon flm, 1 K ohm ?1%, 1/2 w
A6R2
Not Assigned
A6R3
2100-0394
R: var, ww, lin taper, 300 ohms ?20%, 1 w
A6R4
0727-0747
R: fxd, carbon flm, 750 ohms ?1%, 1/2 w
A6R5
2100-0394
R: var, ww, lin taper, 300 ohms ?20%, 1 w
A6R6
0728-0011
R: fxd, carbon flm, 360 ohms ?170, 1/2 w
A6R7
2100-0394
R: var, ww, lin taper, 300 ohms ?20%, 1 w
A6R8
0728-0010
R: fxd, carbon urn, 220 ohms ?.1%, 1/2 w
A6R9 thru
Not Assigned
A6R13
A6R14
2100-0394
R: var, ww, lin taper, 300 ohms ?20%, 1 w
A6R15
Not Assigned
A6R16
0758-0048
R: fxd, met flm, 8.2 K ohms ?5%, 1/2 w
A6R17
0727-0866
R: fxd, carbon flm, 180 ohms 1-1%, 1/2 w
A6R18
2100-0394
R: var, ww, lin taper, 300 ohms ?20%, 1 w
A6R19
Not Assigned
A6R20
2100-0395
R: var, comp, lin taper, 300 ohms 120%, 1/4 w
A6R21
0727-0475
R: fxd, deposit carbon, 970 ohms ?0.5%, 1/2 w
i'ee introduction to this section
6_4 Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
01566-3
Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
Model 410C
Table 6-1. Reference Designation Index (Cont'd)
Section VI
Table 6-1
REFERENCE
DESIGNATION'
V PART NO.
DESCRIPTION
NOTE
A7
410C-65C
Board ass'y - power supply, includes:
C1 R1 thru 4
CR6, 8 R7, 8, 10
A7C1
0140-0041
C: fxd, mica, 100 pf ?5%, 500 vdcw
A7CR1 thru
Not Assigned
A7CR5
A7CR6
1902-0026
Diode: breakdown junction, 36.5 v ?10%, 0.4 w
A7CR7
Not Assigned
A7CR8
1902-0049
Diode: breakdown junction, 6.19 v ?5%, 0.4 w
A7R1 and
0764-0003
R: fxd, met flm, 3.3 K ohms ?5%, 2 w
A7R2
A7R3
0758-0018
R: fxd, met flm, 15 K ohms ?5%, 1/2 w
A7R4
0764-0026
R: fxd, met flm, 13 K ohms ?5%, 2 w
A7R5 and
Not Assigned
A7R6
A7R7
0758-0069
R: fxd, met flm, 1.1 K ohm ?5%, 1/2 w
A7R8
0758-0070
R: fxd, met flm, 1.2 K ohms ?5%, 1/2 w
A7R9
Not Assigned
A7R10
0758-0083
R: fxd, met flm, 68 ohms ?5%, 1/2 w
A8
11036A
AC Probe ass'y (V Model 11036A, complete)
C1, 2 R1
P1 V1
A8C1
Not separately replaceable, part of AC Probe ass'y
(11036A)
A8C2
Not separately replaceable, part of AC Probe ass'y
(11036A)
A8P1
1251-0209
Plug: telephone, 3 conductor
A8R1
Not separately replaceable, part of AC Probe ass'y
(11036A)
A8V1
1920-0010
Tube: electron, EA53, diode
Cl
0170-0021
C: fxd, my, 4700 pf ?10%, 400 vdcw
C2
0160-0001
C: fxd, my, 0.1 pf ?10%, 600 vdcw
C3
0150-0023
C: fxd, ceramic, 2000 pf ?20%, 1000 vdcw
C4
Not Assigned
C5
0180-0125
C: fxd, elect, 4 sect, 4 x 20 if, 450 vdcw
C6
0180-0153
C: fxd, elect, 2 sect, 2 x 1200 ?f, 20 vdcw
CR1 and
1901-0036
Diode: si, 300 ma
CR2
CR3 and
1901-0049
Diode: si, 500 ma
CR4
CR5 and
Not Assigned
CR6
CR7
1902-0327
Diode: breakdown junction, 9.09 v ?10%, '1.5 w
D61
1450-0106
Light Indicator: A1C neon (p/o S3)
Fl
2110-0018
Fuse: cartridge, slo-blo, 0.25 amp, 125 v
# See introduction to this section
01566-3Approved For Release 2001/04/20: CIA-RDP70600584R000100280001-3
6-5
sectownwed For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
Table 6-1
E'ahi 6-1. Reference Designation Index (Cont'd)
Model 410C
REFERENCE
DESIGNATION
4.) PART NO.
DESCRIPTION
NOTE
31
1251-0200
Jack: telephone, 3 conductor
32
Not Assigned
J3
1251-0148
Connect: power cord receptacle
M1
1120-0317
Meter: 0-1 ma
Q1
1850-0098
Transistor: germanium, PNP
R1
0727-0274
R.: fxd, carbon flm, 1 megohm ?11%, 1/2 w
R2
0758-0086
R: fxd, met flm, 100 ohms ?5%, 1/4 w
R3
2100-0415
R: var, ww, lin taper, 25 ohms ?10%, 2 w
R4
Not Assigned
R5
0687-6831
R: fxd, comp, 68 K ohms ?10%, 1/2 w
S3
3101-0100
Swatch: SPST, pushbutton, w/pilot light
S4
3101-0033
Switch: DPDT, slide
Ti
9100-0174
Transformer: power
W1
8120-0078
Cable, Power: 3 conductor, 7-1/2 ft. long, w/NEMA
plug
XQ1
1200-0044
Socket, transistor: TO-3
See introduction to this section
6-6 Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
01566-3
Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
Model 410C
Table 6-2. Replaceable Parts
Section VI
Table 6-2
* PART NO.
DESCRIPTION
MFR
MFR PART NO.
TQ
410C-19A
Switch ass' y - range, includes:
28480
410C-19A
1
R1 thru 4 R30 thru 33
R6, 7 S2
R10 thru 26
410C-19B
Switch ass' y - selector, includes:
28480
410C-19B
1
R1, 2 R10
R5 thru 7 Si
410C-26A
R: fxd, 0.3 ohms
28480
410C-26A
1
410C-26B
R: fxd, 0.7 ohms
28480
410C-26B
1
410C-65A
Board ass'y-amplifier, includes:
28480
410C-65A
1
Cl, 2 R7 thru 9
C4 thru 6 R12 thru 15
CB, 9 R18 thru 21
C11 thru 14 R24 thru 26
C16 R30
CR1, 2 Qi, 2
R1 thru 3 V1
R5
410C-65B
Board ass'y - calibrator, includes:
28480
410C-65B
1
CR1 R14
R1 R16 thru 18
R3 thru 8 R20, 21
410C-65C
Board ass'y - power supply, includes:
28480
410C-65C
1
Ci R1 thru 4
CR6, 8 R7, 8, 10
0140-0041
C: fxd, mica, 100 pf ?5%, 500 vdcw
04062
RCM15E101J
1
0140-0154
C: fxd, mica, 1300 pf ?5%, 500 vdcw
14655
RCM15E101K
1
0140-0208
C: fxd, mica, 680 pf ?5%, 300 vdcw
00853
obd #
1
0150-0023
C: fxd, ceramic, 2000 pf ?20%, 100 vdcw
56289
19C203A
1
0150-0096
C: fxd, ceramic, 0.05 if, 100 vdcw
72982
845-X5V-5032
1
0160-0001
C: fxd, my 0.1 uf ?10%, 600 vdcw
56289
160P10496
1
0160-0161
C: fxd, my, 0.01 lif, 200 vdcw
56289
192P10392
1
0160-0200
C: fxd, my, 0.22 if ?20%, 200 vdcw
72354
F307C224M
2
0160-0209
C: fxd, my, 0.33 lif ?20%, 200 vdcw
72354
F307C334M
1
0170-0018
C: fxd, my, 1 pif ?5%, 200 vdcw
84411
Hew 4/
1
0170-0021
C: fxd, my, 4700 pf ?10%, 400 vdcw
84411
620SJ0047
1
0170-0030
C: fxd, poly, 0.1 tif ?10%, 50 vdcw
56289
P136072
1
0170-0077
C: fxd, poly, 0.047 uf ?10%, 50 vdcw
56289
P130649
1
0180-0039
C: fxd, elect, 100 if, 12 vdcw
56289
D32697
1
0180-0094
C: fxd, elect, 100 tif, 25 vdcw
56289
30D107G025H4
1
0180-0125
C: fxd, elect, 4 sect, 4 x 20 p.f, 450 vdcw
00853
Type PLI
1
0180-0153
C: fxd, elect, 2 sect, 2 x 1200 !if, 20 vdcw
00853
4S4039
1
0686-1021
R: fxd, comp, 1 K ohm ?10%, 1/2 w
01121
EB1021
1
0687-1011
R: fxd, comp, 100 ohms ?10%, 1/2 w
01121
EB1011
1
0687-1021
R: fxd, comp, 1 K ohm ?10%, 1/2 w
01121
EB1021
2
# See introduction to this section
01556-3Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
6-7
Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
Section VI
Table 6-2
Table 6-2. Replaceable Parts (Cont'd)
Model 410C
PART NO.
DESCRIPTION
MFR
MFR PART NO.
TQ
0687-1031
R: fxd, comp, 10 K ohms ?10%, 1/2 w
01121
EB1031
1
0687-1531
R: fxd, comp, 15 K ohms ?10%, 1/2 w
01121
EB1531
1
0687-1851
R: fxd, comp, 1.8 megohms ?10%, 1/2w
01121
EB1851
1
0687-2221
R: fxd, comp, 2.2 K ohms ?10%, 1/2 w
01121
EB2221
1
0687-2751
R: fxd, 2.7 megohms ?10%, 1/2w
01121
EB2751
1
0687-4701
R: fxd, comp, 47 ohms ?10%, 1/2 w
01121
EB4701
1
0687-4731
R: fxd, comp, 47 K ohms ?10%, 1/2 w
01121
EB4731
1
0687-5661
R: fxd, comp, 56 megohms ?10%, 1/2 w
01121
EB5661
2
0687-6831
R: fxd, comp, 68 K ohms ?10%, 1/2 w
01121
EB6831
1
0687-6841
R: fxd, comp, 680 K ohms ?10%, 1/2 w
01121
EB6841
1
0727-0004
R: fxd, deposit carbon flm, 5 ohms ?1%, 1/2 w
94459
CVS
1
0727-0031
R: fxd, carbon ulna, 60 ohms ?1%, 1/2 w
01295
DC1/2PR
1
0727-0274
R: fxd, carbon flm, 1 megohm ?1%, 1/2 w
94459
CVF
1
0727-0445
R: fxd, carbon flm, 2 ohms ?170, 1/2 w
94459
CVS
1
0727-0446
R: fxd, carbon flm, 7 ohms ?1%, 1/2 w
94459
CVS
1
0727-0448
R: fxd, carbon flm, 20 ohms ?1%, 1/2 w
94459
CVF
2
0727-0449
R: fxd, carbon flm, 70 ohms ?1%, 1/2 w
94459
CVF
1
0727-0450
R: fxd, carbon flm, 200 ohms ?0.5%, 1/2 w
94459
CVF
1
0727-0451
R: fxd, carbon flm, 1 K ohm ?0.5%, 1/2 w
94459
CVF
1
0727-0452
R: fxd, carbon flm, 700 ohms ?0.5%, 1/2 w
94459
CVF
1
0727-0453
R: fxd, carbon flm, 2 K ohms ?0.5%, 1/2 w
94459
CVF
1
0727-0454
R: fxd, carbon flm, 6 K ohms ?0.5%, 1/2 w
94459
CVF
1
0727-0455
R: fxd, carbon flm, 20K ohms ?0.5%, 1/2w
94459
CVF
1
0727-0456
R: fxd, carbon flm, 70 K ohms ?0.5%, 1/2 w
94459
CVF
1
0727-0457
R: fxd, carbon flm, 200 K ohms ?1%, 1/2 w
94459
CVF
1
0727-0458
R: fxd, carbon flm, 700 K ohms ?0.5%, 1/2 w
94459
CVF
1
0727-0459
R: fxd, carbon flm, 2 megohms ?0.5%, 1 w
01295
CD1R
1
0727-0475
R: fxd, deposit carbon, 970 ohms ?0.5%, 1/2 w
94459
CD1/2MR
1
0727-0478
R: fxd, carbon flm, 2.21 megohms ?1%, 1/2 w
94459
CVF
1
0727-0479
R: fxd, carbon flm, 250 ohms ?1%, 1/2 w
94459
CVF
1
0727-0480
R: fxd, carbon flm, 2.32 megohms ?1%, 0.5 w
94459
CVF
1
0727-0701
R: fxd, carbon flm, 895 ohms ?1%, 1/2 w
94459
CVF
1
0727-0747
R: fxd, carbon flm, 750 ohms ?1%, 1/2 w
94459
CVF
2
0727-0751
R: fxd, carbon flm, 1 K ohm ?1%, 1/2 w
94459
CVF
1
0727-0866
R: fxd, carbon flm, 1E0 ohms ?1%, 1/2 w
94459
CVF
1
0727-0948
R: fxd, carbon flm, 10 ohms ?1%, 1/2 w
94459
CVF
1
1)727-0955
R: fxd, carbon urn, 10.5 ohms ?1%, 1/2 w
94459
CVF
1
0728-0004
R: fxd, carbon urn, 1 ohm ?1%, 1/2 w
94459
CVF
2
0728-0010
R: fxd, carbon flm, 220 ohms ?1%, 1/2 w
94459
CVS
1
0728-0011
R: fxd, carbon flm, 360 ohms ?1%, 1/2 w
94459
CVF
1
0730-0176
R: fxd, 6 megohms ?0.5%, 1 w
94459
CVC
1
0733-0018
R: fxd, carbon flm, 89 megohms ?1%, 2 w
03888
HV2000
1
0757-0091
R: fxd, met flm, 18 K ohms ?2%, 1/2 w
07115
C20
1
0757-0163
R: fxd, met flm, 3 K ohms ?2%, 1/2 w
07115
C20
1
0757-0164
R: fxd, met flm, 5.6 K ohms ?2%, 1/2 w
07115
C20
1
0757-0165
R: fxd, met flm, 13 K ohms ?2%, 1/2 w
07115
C20
1
0757-0166
R: fxd, met flm, 30 K ohms ?2%, 1/2 w
07115
C20
2
0758-0018
R: fxd, met flm, 15 K ohms ?5%, 1/2 w
07115
C20
1
0758-0048
R: fxd, met flm, 8.2 K ohms ?5%, 1/2w
07115
C20
1
See introduction to this section
Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
01556-3
Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
Model 410C
Table 6_2. Replaceable Parts (Cont'd)
Section VI
Table 6-2
* PART NO.
DESCRIPTION
MFR
MFR PART NO.
TQ
0758-0069
R: fxd, met Hui, 1.1 K ohm ?5%, 1/2 w
07115
C20
1
0758-0070
R: fxd, met flm, 1.2 K ohms ?5%, 1/2w
07115
C20
1
0758-0083
R: fxd, met flm, 68 ohms ?5%, 1/2 w
07115
C20
1
0758-0086
R: fxd, met flm, 100 ohms ?5%, 1/4 w
07115
C07
1
0764-0003
R: fxd, met flm, 3.3 K ohms ?5%, 2 w
07115
C42S
1
0764-0026
R: fxd, met flm, 13 K ohms ?5%, 2 w
07115
C42S
1
0811-0998
R: fxd, comp, 100 ohms ?1%, 1/4 w
28480
0811-0998
1
1120-0317
Meter: 0 - 1 ma
28480
1120-0317
1
1200-0044
Socket, transistor: TO-3
97913
M7 (PB)
1
1251-0148
Connector, power cord receptacle
82389
AC3G
1
1251-0200
Jack: telephone, 3 conductor
82389
3J-1291
1
1251-0209
Plug: telephone, 3 conductor
82389
2P-1297
1
1450-0106
Light Indicator: A1C neon (p/o S3)
87034
A1C
1
1850-0013
Transistor: germanium, PNP
86684
CP2366
1
1850-0040
Transistor: germanium, PNP
04713
SA591
1
1850-0098
Transistor: germanium, PNP
83298
B-1493
1
1901-0025
Diode: si, 50 ma
93332
D3C72
1
1901-0036
Diode: Si, 300 ma
01841
obd #
1
1901-0049
Diode: s4 500 ma
86684
34934
1
1901-0156
Diode: si, 50 ma
03877
SG3288
1
1902-0026
Diode: breakdown, junction, 36.5 v?10%, 0.4w
04713
SZ10939-343
1
1902-0049
Diode: breakdown, junction, 6.19 v ?5%, 0.4 w
04713
SZ10939-122
1
1902-0327
Diode: breakdown, junction, 9.09 v?10%, 1.5w
12954
obd #
1
1920-0010
Tube electron, EA53, diode
73445
EA53
1
1932-0027
Tube: electron, 12AT7, dual triode
00011
2AT7
1
1990-0020
Ass'y - chopper block, includes:
28480
1990-0020
1
Cl R1, 2
DS1, 2 V1 thru 4
2100-0227
R: var, ww, lin taper, 20 ohms ?10%, 1 w
28480
2100-0227
1
2100-0389
R: var, ww, lin taper, 10 K ohms ?10%, 5 w
28480
2100-0389
1
2100-0394
R: var, ww, lin taper, 300 ohms ?20%, 1 w
11236
Series 110
6
2100-0395
R: var, comp, lin taper, 300 ohms ?20%, 1/4w
71590
Series 5,Type 70-1
1
2100-0396
R: var, ww, lin taper, 10 K ohms ?20%, 1 w
79727
E870PAB
1
2100-0413
R: var, comp, lin taper, 2.5 megohms ?20%,1/4w
71590
Series 5, Type 70-1
1
2100-0415
R: var, comp, lin taper, 25 ohms ?10%, 2 w
08984
FFF-1, Term.
1
X, Y, Z
2100-0442
R: var, comp, lin taper, 40K ohms ?30%, 1/4w
71590
Series 5,Type 70-1
1
2110-0018
Fuse: cartridge, slo-blo, 0.25 amp, 125 v
71400
MDL1/4
1
3101-0033
Switch: slide, DPDT
79727
G-326, 6510
1
Rev . A
3101-0100
Switch: SPST, pushbutton, w/pilot light
87034
SW-624-109
1
8120-0078
Cable, Power: 3 conductor, 7-1/2 ft. long,
w/NEMA plug
70903
KH-4147
1
9100-0174
Transformer: power
28480
9100-0174
1
# See introduction to this section
01556-3 Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
6-9
sectihuroved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
Fable 6-3
Fable 6-3. Replaceable Hardware
Model 410C
(4-0 PART NO,
DESCRIPTION
MFR
MFR PART NO.
TQ
1510-0006
Binding post, black (p/o J2)
28480
1510-0006
1
1510-0007
Binding post, red (p/o J2)
28480
1510-0007
2
11036-42102
Boot, AC plug (p/o 11036A)
28480
11036-42102
1
11036-42101
Boot, AC probe (p/o 11036A)
28480
11036-42101
1
412A-83A
Boot, cable
28480
412A-83A
3
410C-12A
Bracket, connector (used with A3 connector)
28480
410C-12A
1
410C-12B
Bracket, switch (used with A6 connector)
28480
410C-12B
1
1200-0081
Bushing, insulator (used with Q1)
26365
974 Special
2
1410-0091
Bushing, panel (used with A1S1 and A2S2)
28520
SB-437-4
2
0400-0019
Bushing, strain relief
28480
0400-0019
3
410C-1A
Chassis, xfmr
28480
410C-1A
1
410B-21H
Clip, grounding (p/o 11036A)
28480
410B-21H
1
2251-0195
Connector, 10 pin P.C.
02660
143-010-09 (109)
1
1251-0213
Connector, 15 pin P. C.
000XX
SD-615W (125)
1
410B-21P
Contact, Diode (p/o 11036A)
28480
410B-21P
1
3130-0038
Coupler, switch
45255
10X20X1
1
5000-0711
Cover, bottom
28480
5000-0711
1
5000-0703
Cover, side
28480
5000-0703
2
5060-0706
Cover, top
28480
5060-0706
1
5060-0727
Foot Ass'y
28480
5060-0727
2
5060-0703
Frame, side
28480
5060-0703
2
410B-21J
Ground Lead Ass'y (p/c 11036A)
28480
410B-21J
1
5040-0700
Hinge (used with tilt stand)
28480
5040-0700
2
1400-0084
Holder, fuse
75915
342014
1
0340-0086
Insulator, binding post, double
28480
0340-0086
1
0340-0091
Insulator, binding post, triple
28480
0340-0091
1
1520-0001
Insulator, capacitor (used with Cl - C2)
56137
XP
2
0340-0007
Insulator, ceramic standoff
71590
obd#
1
0370-0112
Knob, black bar, concentric
28480
0370-0112
1
0370-0113
Knob, black bar, w/arrow
28480
0370-0113
1
0370-0114
Knob, red, w/arrow
28480
0370-0114
1
0360-0016
Lug, solder, lock, #4
78452
718
1
0360-0007
Lug, solder, #10
78189
2501-10-00
4
0360-0042
Lug, solder, 90?
79963
obd#
2
2260-0001
Nut, hex, 4-40 x 1/4 in,
28480
2260-0001
4
2420-0001
Nut, hex, 6-32 x 5/16 in., w/lock
83385
obd#
4
2820-0001
Nut, hex, 10-32 x 3/8 in.
73743
obd#
3
2950-0006
Nut, hex, 1/4-32 x 3/8 in.
73734
#9000
3
2950-0001
Nut, hex, 3/8-32 x 1/2 in.
73743
obd#
3
2950-0037
Nut, hex, 1/2-16 x 11/16 in.
73915
obd#
1
2950-0038
Nut, hex, 1/2-24 x 11/16 in.
73915
903-12
1
0590-0039
Nut, speed, 6-32
'78553
C6800-632-1
4
0590-0052
Nut, speed, 6-32
78553
C8020-632-4
2
410C-2A
Panel, front
28480
410C-2A
1
410C-2B
Panel, rear
28480
410C-2B
1
410C-41A
Plate, insulator (used with A1S1 and A2S2)
28480
410C-41A
1
_
'ice introduction to this section
6-10 Approved For Release 2001/04/20 : CIA-RDP701300584R000100280001-3
01556-3
Model 4106PProved For Release 2001/04/20: CIA-RDP70600584R000100280001-3
Table 6-3. Replaceable Hardware (Coned)
Section VI
Table 6-3
0) PART NO.
DESCRIPTION
MFR
MFR PART NO.
TQ
1200-0043
Plate, insulator (used with Q1)
71785
294457
1
1251-0209
Plug, telephone (p/o 11036A)
82389
2P-1297
1
410B-21C
Probe contact ass'y
28480
410B-21C
1
410B-21D
Probe head
28480
410B-21D
1
410B-21F
Ring, retainer (p/o 11036A)
28480
410B-21F
1
2200-0006
Screw, machine, 4-40 x 3/8 in. RH
80120
obd#
2
2200-0014
Screw, machine, 4-40 x 9/16 in. RH
80120
obd#
2
2370-0001
Screw, machine, 6-32 x 1/4 in. FH
80120
obd#
20
2390-0007
Screw, machine, 6-32 x 5/16 in. BH, w/lock
83385
obd#
4
2370-0002
Screw, machine, 6-32 x 3/8 in. FH
80120
obd#
8
2370-0003
Screw, machine, 6-32 x 1/2 in. FH
80120
obd#
2
410B-21E
Sleeve (p/o 11036A)
28480
410B-21E
1
1460-0087
Spring, diode contact (p/o 11036A)
91260
obd#
1
1490-0031
Stand, tilt
91260
obd#
1
410C-66A
Support, circuit board (used with A3)
28480
410C-66A
2
410C-21D
Test lead ass'y, COM
28480
410C-21D
1
410C-21C
Test lead ass'y, DCA-OHMS
28480
410C-21C
1
410C-21A
Test lead ass'y, DCV (includes R1)
28480
410C-21A
1
5020-0704
Trim, meter
28480
5020-0704
1
11036-62101
Tube, socket and cable ass'y (p/o 11036A)
28480
11036-62101
1
3050-0066
Washer, flat, #6
73734
obd#
2
3050-0067
Washer, flat, 3/8 in. ID
73734
obd#
3
0900-0016
Washer, fuse holder
76680
622710
1
2190-0005
Washer, lock, #4 external
80120
obd#
2
2190-0004
Washer, lock, #4 internal
78189
SF1904
2
2190-0003
Washer, lock, #4 split
83385
obd#
2
2190-0047
Washer, lock, #6 countersunk
78189
obd#
30
2190-0011
Washer, lock, #10 internal
78189
1910
2
2190-0028
Washer, lock, #10 int/ext
78189
4010-18-00
2
2190-0027
Washer, lock, 1/4 in. internal
78189
1914
3
2190-0022
Washer, lock, 3/8 in. ID
78189
1920
4
2190-0037
Washer, lock, 1/2 in. internal
78189
1224-08
2
1400-0090
Washer, Neoprene
75915
901-2
1
# See introduction to this section
01556-3 Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
6-11
A pp eiiNg rAoved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
APPENDIX
CODE usir OF MANUFACTURERS (Sheet 1 of 2)
Model 410C
The following code numbers are from the Federal Supply Code for Manufacturers Cataloging Handbooks H4-1 (Name to Code)
and H4-2 (Code to Name) and their latest supplements. The date of revision and the date of the supplements used appear at
the bottom of each page. Alphabetical codes have been arbitrarily assigned to suppliers not appearing in the H4 handbooks.
Carlo
Cods
Cede
Cade
Na.
MusufoDturs, Address
Na,
Monufscrorer Addr?ss
Me.
monufsetorsr Address
Na.
Alonufacturor Addres.
1.10000
U.S.A. Common Any suppliei of IL S.
01149
Filmaho Coro. New Yoik, N. Y.
49956
Raytheon Company Lexington, Mass.
74970
C.F. Johnson Co. Waseca, Minn.
MI;
McCoy Electronics Moonl Holly Springs, Pa.
07233
Cinch-Graphis Co CIty of Industry, Calif.
52090
Rowan Control lei Co. Baltimme, Md.
75012
NW-national Resistatce Co. Philadelphia, Pa.
non i
S.ige Corp. Rochesto. N. Y.
01331
Avnet Corp. Los Angeles, Calif.
63743
Ward Leonard Electric MI. Vernon, N. Y.
75173
Jones, Howard B., Eivision
00331
Huniclail Co. Callon. Calif.
0726.3
Fairchild Semiconductor Coro.
54294
sha Halms MN, Ca. Se IMa, NC.
of Cinch Mfg. Coro. Chicago,
01330
Nestles Corp. New York, N.Y.
Mountain View, Calif.
55026
Simpson Electiic Co. Chicago, III.
75374
James Knighls Co. Sandwich, Ill.
003/1
Garlock Packing Co.,
07322
Minnesota limtiOer Co. Minneapolis, Minn.
55933
Sonotone Corp. Elmsfoid, N.Y.
76302
Kulka Electric Corpo-,tion Mt. Vernon, N.Y.
Lleciionic rhoducts Sin. Camden, N.J.
07337
The Birtehei Cnro. Los Angeles, Calif.
95938
Sorenson 8 Co., Inc, So, Norwalk, Conn.
751318
Lenz Electric Mfg, Co. Chicago, Ill.
nI1151,
Aerovox Corp. New Bedford, Mass.
07700
Technical Mn Products Springfield N.J.
56137
Spaulding Fibre Co., Inc. Tonawanda. N.Y.
75915
Littlefuse Inc. Des Plaines, Ill.
09/79
Any, In:. Harrisburg, Pa.
07910
Conlinental Ceylon Coop, Havethoine,
56289
Spiague Electric. Co. Nortn Adams, Mass,
76005
Lord Mfg. Co. Erie, Pa.
00781
Aircraft Radio Corp. Boonton, N.J.
31953
Rheem Semixonnuctra Con unlain View, Calif
59146
Telex, Inc. St. Paul. Minn.
76210
C.W. Marwedel San Francisco, Calif.
13813
Northern Engineeong Laboialones, lac
17966
Shockley SP11,1.C.1.111dIld01
59730
Thomas & Betts Co. Elizabeth 1, N.J.
76433
Micamoid Electronic Afg, Corp. Brooklyn, N.Y.
iLIPSO
ituilington. Wis.
Songamo Elector Company.
97980
I arivatnr el Palo Alla, Cala,
Boonton Radio (lop, Boonlon, N.J.
60741
61775
Topplett Electt cal Inc_ Brunton, Ohio
Union Switch and Signal, Div. of
76487
76493
James Millen Mfg, Cr., Inn, Malden. Mass.
1.1. Miller Co. Los Angeles, Calif.
11,0111 Division iCapacitors) Marion, Ill,
00195
U.S. Engineering Co. Los Angeles, Calif
Westinghouse Air Brake Co. Swissvale, Pa.
76530
Monadnock Mills San Leandro, Calif.
00809
Due Engineering Co. 1 an Angeles, Calif.
08353
Buigess Baltory Co.
62119
Universal Noll ic Co. Owosso, Mich.
76515
Mueller Electric Co. Cleveland, Obi,
HUAI
Coll E. Poimes Cola. I on Angeles. Calif
Niagara Falls, Ontario, Canada.
63743
Ward-Leonard Electric Co. Mt, Vernon, N.Y.
76054
Oak Manulacturing Cr. Crystal Lake, Ill.
owl
Allen Bradley Co. Milwaukee, Wis.
93717
Sloan Campo,/ Milbank, Calif.
64959
Western Electric Co., Inc. has York, N.Y.
77068
Bendis Pacific Divis on of
111251,
Dillon Industries, Inc. Beverly 111115, Calil.
09718
Cannon Elect- it Co. Phoenix Div, Phoenix, Alla.
65092
Weston Inst. Div. of Daystram, Inc. Newark, N.J.
Bendix Corp. No. Hollywood, Calil.
Ill/f'
TRW Semiconductors Inc. Lawndale, Calif.
10792
CBS Emictroincs Sernicond iclor
66295
mitek manufactimne Co. Chicago 23, III.
77075
Pacific Metals Co. San Francisco, Calif.
01299
Texas Instruments, Inc.
Oneiatior-ciiiv.of C.11.5.1nc. Lowell, Mass,
66346
Wollensak Optical Co. Rochester, N.Y.
77221
Phaostran Instrument and
frani-islor Products Div. Dallas, Texas
08989
Mel-Raio Indianapolis, Ind.
70276
Allen Mfg. Co. Hartford, Cann.
Electronic Co. South Pasadena, Calif.
01349
lith61
The Chine Mfg. Co. Alliance. Ohio
Chas.-Irak Corp. Indianapolis. Ind.
39026
09139
Babcock Relay, Inc. Costa Mesa, Calif,
Texas Capacilor Co. Houston, Texas
70309
70319
Allied Control Co., Inc New 'fork, N.Y.
Allmetal Screw Nod, Co., Inc.
77255
77252
Phoell Mfg, Co. Chicago, III,
Philadelphia Steel and Wire Corp.
91585
Pacific Belays, Inc. Van Nuys, Calif.
09145
Atone Electionies Son Valley, Calif,
Golden City, N.Y.
Philadelphia, Pa.
01930
Ameiack Corp Rockford. III.
09250
Elect. Assembliei. Inc. Chicago, Ill,
70485
Atlantic India Rubber Wolks, Inc. Chicago, III,
77342
Potter and Brumfield, Div. of American
01961
Pulse El-annealing Co. Santa C arc Calif.
09969
Mallory Balleir Cc. ol
70563
Amperite Co., Inc. New York, N.Y.
Machine and Founhy Princeton, Ind,
02114
FeHoscuoe Corp of America Saugeities. N.Y
Canada. 1 Id Tricot?, Ontario, Canada
70903
Belden Mfg. Co. Chicago, Ill,
77630
Radio Condenser Co. Camden, N.J.
.122dr,
Cole Mfg. Co. Palo Allo,
09664
The Brisiol Co Wateibury, Conn,
70998
Bird Elechonic Corp, Cleveland, Ohio
77638
Radio Receptor Co., Inc. Brooklyn, N.Y.
030101
Amphenol-Boig Electionics Corp. Chicago, Ill.
10714
General Western Corp.
71002
Birnbach Radio Co. New York, N.Y.
77761
Resistance Products Co. Harrisburg, Pa.
:12715
Rodin Ctrs. ol America, Serniconductai
Los Angeles, Calif.
71011
Boston Gear Works Div_ d
77969
Rubbercrall Corp, of Calif, Torrance, Calif.
md Woleuals Pro Someiville, N. I.
19411
ToTal, Inc. Berkeley, Calif.
Murray Co. of Texas Quincy, Mass.
78189
Shakeproof Division of Illinois
iic/71
Vocaline Co al Antenna, Inc.
10146
Carbaruridurn 1e. Niagara Falls N Y.
71218
Bud Radio Inc. Cleveland, Olio
Tool Works Elgin, Ill.
ill Maybrook, Cann.
11236
CTS of Berne Inc Boole. Ind.
71286
Camloc Fastenei Corp. Paramus, N.J.
78283
Signal Indicator Corp. New York, N.Y.
ildraios tireureerole Co. San Feinando, Calif.
11237
Chicago Telenh,ne of Cali orn a, Inc.
71313
Allen D. Cardwell Electronic
78290
Strulhers.-Dunn Inc. Pitman, N.J.
11508
3.E. Sealcoilductai Products Dent. Syiacuse, N.Y.
So. Pasadena,
Prod, Corp. Plainville, Conn.
78152
Thompson-Bremer & (u. Chicago, Ill,
Ave, Mar hine & Tool Co. Dayton, Ohio
11312
Microwave F-comnoics Coif Palo Alto, Calif.
71400
Bussmann Fuse Div. of McGraw-
78471
Tilley Mfg. Ca. San Francisco, Calif.
1371/
011e110 Inc. Er Monte, Calif.
11539
Duncan Electronic Inc. Santa Ana. Calif.
Enison Co. SI. Louis, Mo.
713408
Stackpole Carbon Co. St. Marys, Pa.
13311
Transition Electionic Corp. Wakefield, Mass.
11111
General Instromoot Coroniation
71435
Chicago Condenser Corp. Chicago, III,
78193
Standard Thome. Coo, Waltham, Mass.
13838
Pyrolilm Resrslor Co Morristown. N.J.
Sersiconfortor Division Newark, N.J.
71450
CTS Corp. Elkhart, Ind.
713553
Tinnerman Products, loc. Cleveland, Ohio
11351
Air Marine Motois, Inc. 1. os Angeles, Calif.
1111/
Imperial Elecf Nile, Inc. Buena Park, Calif.
71468
Cannon Electric Co. Los Angeles, Calif.
70790
Transformer Engineer.: Pasadena, Calif.
94009
Allow, Hart and Hegeman Elect. Ca.
11871
Melahs, Inc. Pala Alto, Calif.
71471
Cinema Engineering Co. 13urbaok, Calif.
70917
Ucinite Co. tiewtonville, Mass.
Ilartioid, Goon.
02597
Clarostat Mfg LI. Dover, N.H.
71482
C. F. Clare & Co. Chicago, Ill.
79142
Meader Rool, Inc. Hartford, Conn.
341112
Elpenco Products Co. New York, N.Y.
12099
Nippon Finn o. Ltd. Tokyo, Japan
71590
Cenlialab Div of Globe Union Inc.
79251
Wenco Mfg. Co. Chicago, III.
1.1322
111 CL Din :ion of Aerovox Nellie Beach, S.C.
11930
Delta Sniniconitti lir Inc. Newpoil Beach, Calif.
Milwaukee, Wis.
79727
Continental.Wirt Elecironics Corp.
114/98
Elgin Nalional Watch Co..
10103
Thermollav Dallas, Texas
71700
The Cornish Wile Co. New Yank, N.Y.
Philadelphia, Pa.
Electionics Division Burbank, Calif.
13396
Telefonken IG 11 1,/I. r Hannover, Germany
71744
Chicago Miniature Lamp Works Chicago, Ill.
79963
Zierick Mfg. Corp. New Rochelle, N.Y.
.14 in4
Dyinec Division of Hewlett-Packard Co.
111115
Midland Mrs. ,i- Kansas City, Kansas
71753
A.O. Smith Corp., Ciowley Otv.
80031
Mapco Division of Sessions
Palo Alto.
11999
Sem-Tech Newbury Pall, Calif.
West Orange, N.J.
Clock Co. Morristown, N.J.
ilitiS1
Sylvaina Tann Prods.. Inc.
14193
Cold. Rasistri Sonia Monica, Calif.
71785
Cinch Mfg, Corp Chicago, Ill,
83120
SchniLzer Alloy Products Elizabeth, N.J.
I Inctronic I le 1510, Moontain Area, Calif
11798
Amemran Enscronents, Inc Conshohocken, Pa.
71989
Dow Corning Corp. Midland, Mich,
80130
Times Facsimile Carr. New look, N.Y.
131111
Liolorola, Inc.. Semiconductoi Prod. 000.
11655
Cninell Dubitior Ely, Cor To, Plainfield, N.J.
72092
EiteltMcCullough Inc. San Bruno, Calif.
00131
Electronic Industries Association. Any brand
Phoenix, Ammana
14960
Williams Mfg 7 .. San one, Calif.
72136
Electro Motive Mfg, Co., Ins.
lose meeting EIA slandards Washington, D.C.
191713
Jiltron Cr. Inc., Waste!, Div, Culyei City, Calif.
19909
The Damen Cc Livingston, N.J.
Conn,
00207
Unimax Switch, Div. 0
114113
Automat, Electric Co. Northlake, 111.
16037
Splice Pine M-no Co Spruce Pine, N. C.
71707
Coto Coil Co., Inc. Providence, A. I.
W. L. Masson Carp. Wallingford, Conn.
1
u1796
Aolonalli Electric Sales Carp. Noithloke, Ill.
Sequoia Toe I Cable Co. Redwood City, Calif.
16352
10503
Computer Dioce Como Lodi, N. J.
To Hir-Amsco Pcp-mation
72354
72619
John E. Fast 0175. Chicago, III,
Dialighl COP, Elrooklyn, N.Y.
00223
00248
United Transformer Corp. New York, N.Y.
Oxfpd Electric Coop. Chicago, III.
i
C9-I surna Co. El Millie, Calif.
vie Island C ty I, N.Y.
72656
General Ceramics Corp. Keasbey, N.J.
00294
Bourns Laboratories, Inc. Riverside, Calif.
313/0
A Motor Company Chicago 44, III.
1;758
Delco Radio D y of G.M. Corp. Kokomo, Ind,
/2699
General Instrument Coil.,
00411
Acro DN. of Robertshaw
.101105
I werliell trentLiv Plastics. Inc.
11073
3.1. DuPont .1.. Cr., Inc. Wilmioglon, Del.
Semiconduclor Neyalli, N.J.
Fullon Controls Co. Columbus 16, Ohio
i Ange Calif.
11115
f clipse PionerL, Div. of
72758
Girard-Hopkins Oakland, Calif.
00481
All Stu Products Inc. Defiance, Ohio
WeslInghr nse k lecInn Corp.
Ay-0tion Corp. Teterboro, N.J.
/2765
Drake Mfg. Co. Chicago, III,
80509
Avery Adhesive Labe Corp. Monrovia, Calif.
Semi COTIOLC101 Dept, Yoongwood. Pa.
119110
Thomas A. Fronimin Industries,
72825
Hugh H. Eby Inc. Philadelphia, Pa,
00583
Haminerlund Co., Inc. New York, N.Y.
tilliodix. Inc. San Male, Calif.
Div. of 4,1,;,10 Ed15011 Go, Weal Orange, N.J.
72924
Godernan Co. Chicago, III,
80610
Stevens, Arnold, Co. Inc. Boston, Mass.
/1091
IllonolinniC Engineering Co Sunnyvale, Calif.
1/101
Elcatra Manofactiring Co. Kansas Cily. No.
72964
Robert M. Hadley Co. Los Angeles, Calif.
81030
International Instrumetis, Inc
1.0521
Barber Cl Irian Co. Rockford, Ill.
20103
Eleclinnic Tiihe Coip. Philadeiphia. Pa.
72982
Erie Resistor Core. Erie, Pe.
New Haven, Conn,
115115
1 Olen Optical Co.
01275
Executivo, In,. New Yolk, N.Y.
73061
Hansen Mfg. Cu., Inc. Princeton Ind.
81073
Grayhill Co. LaGrange, III,
Roslyn Heights, , 0,0 101004. N.Y.
(1073
lansteel Melailuryi_al Corp. No. Chicago, Ill.
73076
H. N. Harper Co. Chicago, III.
81095
Triad Transfernier Cola. Venice, Calif.
0E100
MelL000loan Telecommunications Corp.,
21335
The Fain Beciing Co. New Airfuno, Corn.
73138
Helipot Div. of Beckman
81312
Winchester Electronics Co., Inc. lonvalk, Conn.
:intro 70p. Division Brooklyn. N.Y.
2r964
Fed. Telephone Radio Corp. Cl,IIae, N.J.
Instruments, Ins, Fullerlon, Calil.
81349
Military Specification
1E7,13
Stewart Engineering Ca. Santa Cruz, Calil.
31446
Calera I Elect- '.0. Scheneclady, N.Y.
73293
Hughes Products Division of
81415
Wilkor Products, Inc. Cleveland, Ohio
Ea/ti
Wrkelield Engineering Inc Wakefield, Mass
20455
G.E.. Panic in Nola Park, Cleveland, Ohio
Hughes Aircraft Co. Newpoit Beach, Calif.
81453
Raylheon Mfg. Co., Industrial Components
1,104
9050,00 Co. Bridgeport, Conn.
23555
fieueral Radio Cll. Wes! Concord, Mass.
73/15
Amperes Electronic Co.. Div. of North
Div., Indust, Tube Operations Newton, Mass,
151/5
Bausch and Lomb Oplical Co. Rochester, N.Y.
293/5
Cries Region- Co. New Rochelle, N.Y.
American Phillips Co, Inc. Hicksville, N.Y.
81483
International Rectilier Corp. El Segundo, Calif.
05407
F 0,5 Eicducts CO. of America Chicago III.
71.112
Grobet File Cl'. 0-neima, Inc. Carlstadt, N.J.
73490
Beckman Helipot Coip. So, Pasadena, Calif.
81541
The Amps Products Co. Cambridge, Mass.
:131111
Amaiorn ElectioniC
7wrin?
Hamdlon Natcn ( Lancaster, Pa.
73509
Bradley Semiconductoi Corp. Hamden, Conn.
01860
Barry Controls, Inc. Waterlown, Mass.
Horde,. Co 101 New Rochelle. N Y.
71010
liewiell-Packaid Co. Pala Alto, Calif.
73559
Carling Electric. Inc. Hartford, Conn.
02042
Carter Parts Co. Skokie, III,
CriSSS
Horde Eli-clrical instrument Co. Inc,
Penacook, N.H.
10171
19439
0,E. Ron, 151, Trthe Dept OwensbiNo. By,
Lactic-rim Inc. Chicago. III.
73682
73734
George K. Goren Co., Inc. Philadelphia, Pa.
Federal Screw Prod. Co. Chicago,
82142
Jeffers Electronics Division of
Spem Carbon Co. Du Bois, Pa.
.0,61
A_ I Serino; Dnilsron or Nuclear COM.
11111mm-I Phrw?nrw Ailnona
17,116
3/942
Stony/yr, Curl' Hawkeihory, Ontario, Canada
P.R. Mallois 3, Co., Inc. Indianapolis. Ind.
73743
73793
Fischer Special Mfg. Co. Cincinnali, Ohio
The General Industries Co. Elyria, Olin
82170
02209
Allen B. DuMonl Labs. Inc. Clifton, N.J.
Maguire Industries, In, Greenwich, Cann.
ilb312
I orcretcr Mfg. Co.. West DIP. Van Nays. Cala,
10541
Mechanical locr.iorrios Prod. Co. Moon. Ohio
73846
Goshen Stamping 8, Tool Co. Goshen, Ind.
02219
Sylvania Electric Prod, Inc.
NI V;
Corn no Glass Works
nt.lr C:,,DOCNS Dart. Brarlfold Pa.
:0920
:1190
Oir0000re Pien.siim Bearings, Inc. Keene, N.H.
Mater Co, Chicago, Ill.
73899
73905
JED Electronics Corp. Biooklyn, N. Y.
Jennings Radio Mfg. Co. San Jose, Cali'.
02376
Electronic Tube Div. Emponurn, Pa,
Astros Cu, East Newark, N.J.
[Lydian So. Pasadena, Calif.
41,91
C. A. Noryreo co. Englewood. Colo.
79276
Signalite Inc. Neptune, N.J.
02389
Switchcraft, Inc. Chicago, III.
(.1111
rannislor F lerunnws Clio. IhnneannIts, Minn.
Ohmite MI5. C.:. Skokie, IQ.
74455
Wiens, and Sons Winchester, Mass.
02647
Metals and Contiols, Inc.. Div. ol
irt,tnighouse Coo.
07901
Polaroid Corp. Cambridge, Mass.
74861
.1.11.
Industual Condenser Corp. Chicago, III.
Texas Instruments, Inc.,
Folfrill, I an oo. LIR ia, N.Y
19E19
Picnision Ther ,crieter ana
lost. Cu. Philadelphia, Pa,
74868
R. F. Pinducts Division or Amphenol-
Rnig Electronics Corp. Danhurv, Conn.
From
Spencer Prods, Allleboro, Mass.
FSC, Handbook 5upplernents
C0015
37
H4 I Dated OCTOBER 1963
frwvised July 11 !...4
114 0 Dated MARCH 1962
Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
Model Approved0C For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
41
APPENDIX
CODE LIST OF MANUFACTURERS (Sheet 2 of 2)
Appendix A
Cod?
Code
Code
Cod?
No,
Manufacturer Address
No.
Manufacturer Adds...
Na. Manufacturer Address
Na. Manufacturer Address
87066
Research Products Corp. Madison, Wis.
89636
Carter Parls Div. ol Economy Baler Co.
95263 Leman Mfg. Co., Inc, New York, N.Y.
THE FOLLOWING H-P VENDORS HAVE MO NUM-
82877
Rotron Manufacturing Co.. Inc. Woodslock, N.Y.
Chicago, Ill.
95264 Lerco Clectronrcs, so, Burbank, Cal/I.
BER ASSIGNED IN THE LATEST SUPPLEMENT TO
82893
Vector El.Ironic Co. Glendale, Cant.
89665
United Transformer Co. Chicago, III.
95265 National Coil Co. Sheridan, Wyo.
THE FEDERAL SUPPLY CODE FOR MANUFAC-
03053
Western Washer Mb, Co. Los Angeles, Calif.
901i9
U.S. Rubber Co., Mechanical
95235 Vitramon, Inc. Bridgeport, Conn.
TURERS HANDBOOK.
83058
Carr Fasten. Co. Cainbridge, Mass.
Goods Dry. Passaic, N.J.
95348 Gordas Corp. Bloomfield, N.J.
83086
flew Hampshrie Ball Bearing, Inc.
90981
Bearing Engineering Co. San Francisco, Calif.
95354 Idelhocle Mfg. Co. Chicago, Ill,
00000 JED Electronics Corp. Van Nuys, Cali!.
Peterborough, N.H.
91260
COrin01 Spring 1711g. Co. San Francisco, Calif.
95907 Yleckesso Co. Chicago, Ill.
10000 Tranex Company Mountain View, Calif.
83125
Pyramid Electric Co. Darlington, S.C.
91345
Miller Drat & Nameplate Co. El Monte, Calif.
96067 Huggins Laboratories Sunnyvale. Calif,
10000 Western Devices, Inc. Inglewood, Calif.
83148
Electra Cords Co. Los Angeles, Calif,
91410
Radio Materials Co. Chicago, III.
96095 HO 81443i011 of Av.. Olean, N.Y.
10000 WInchesler Electronrcs, Inc.
83186
Victory Engineering Corp. Unron, N.J.
91506
Augal Brothers'. Inc. Altleboro, Mass.
96256 Thordarson-Meissner Div. of
Santa Monica, Calif.
83298
Bendix Coro., Red Bank Div. Red Bank, N.J.
91637
Dale Electronics, Inc. Columbus, Nebr.
Maguire Industries, Inc. II. Carmel, Ill.
0000F Mateo Tool and Die Los Angeles, Calif.
83315
Hubbell Corp. Mundelein, Ill.
91662
[lot Corp. Philadelphia, Pa.
96296 Solar Manufacturing Co. Los Angeles, Calif.
001)(40 Western Coil Div. of Automatre
83330
Smith, Herman H., Inc. Brooklyn, N.Y.
9113/
Gram. Mfg. Co., Inc. Wakefield, Mass,
96330 Carlton Screw Co. Chicago, III.
Ind., Inc. Redwood City, Calif,
83385
Central Screw Co. Chicago, Ill.
9182/
K F Development Co. Redwood City. Cali!.
96341 Mrcrowave Associates, Inc. Burlington, Mass.
COOON Nahm-Bros, Sering Co. San Leandro, Calif,
83501
Gavrtt Wire and Cable Co.,
Div. ol Amerace Corp. Brooklield, Mass.
91929
Minneapolis?Honnywell Regulator Co..
Micieswitch Div. Freeport, III.
96501 Excel Transformer Co. Oakland, Calif.
97464 Industrial Relaining Ring Co. Irvington, N.J.
0000P Ty-Car Mfg. Co., Inc. Holliston, Mass.
00008 Webster Electronics Co. Inc. New York, N.Y.
83594
Burroughs Corp.,
92160
I'm-Connector Corp. Peabody, Mass.
97539 Automabc and Precision Mfg. Co
00002 'Willow Leather Producls Corp. Newark, N.J.
Electronic Tube Div. Plarnfield, N.J.
92196
Universal Metal Prod., Inc. 8450017 Puente, Card.
Yonkers, N.Y.
0000/1 British Rothe Electronics Ltd. Washington, D.C.
83740
Eveready flattery New York. N.Y.
92367
Elgeet Optical Co., Inc. Rochester, N.Y.
97966 CBS Erectronics,
000413 ETA England
83777
Model Eng. and Mfg., Inc. Huntington, Ind.
92607
Tinsolile Insulated Vie Co. Tarrytown, N.Y.
Div. of C.B.S.. Inc. Danvers, Mass.
003RD Indiana General Corp., Elect. Dry. Indiana
83821
Loyd Scruggs Co. Fest., Mc,
93332
Sylvania Electric Prod. 100.,
97979 Reon Resistor Corp. Yonkers, N.Y.
00000 Urns Instrument Inc. Mt. Kisco, N.Y.
84121
Arco Electronis. Inc. New York, N.Y.
Semmonductor Dud. Woburn, Mass.
98141 Axel Brothers Inc. Jamaica, N.Y.
000513 Precision Inshurnent iDemponents Co.
84396
0.3. Glesener Co., Inc. San Francisco, Calif.
93369
Robbins and Myers, Inc. New York, N.Y.
98159 Rubber Tack, Inc. Gardena, Calif.
Van Nuys, Calif.
84411
Good All ElecInc Mfg. Co. Ogallala, Neb.
93410
Stevens Mfg. Co., Inc. Mansfield, Ohio
98220 Francis L. Mosley Pasadena, Calif.
000MM Rubber Eng. & Development Hayward, Calif.
84970
Sarkes Tarman, Inc. Bloomington, Ind.
93/88
Hovnirr 3. Smith Inc. Peri Monmouth. N. J.
98274 Microdot, Inc. So, Pasadena, Calif.
DONN A D Manufacturing Co. San Jose 27, Calif.
85454
Boonton Molerng Company Boonton, N.J.
93919
G. V. ConVols LivIngston, N. J.
98291 Sea leclro Corp. Mamaroneck, N.Y.
0031919 Coollren Oakland, Calif.
85471
A.B. 8007 Co. San Francisco, Calif.
93983
Insulate-Van Norman Ind., Inc.
98405 Carad Corp. Redwood City, Calif.
000011 Radro Industries Des Plaines, III.
215474
A.M. Dracamonte & Co. San Francisco, Calif.
Electronic Duirsion Manchester, N.H.
98731 General Mills Minneapolis, Minn.
00030 Control of Elgin Watch Co. Burbank, Calif.
85660
Kodnd Krords Inc. New Haven, Conn.
9413i
General Cable Corp. Bayonne, N.J.
98821 North Hills Electric Co. Mineola, N.Y.
000514 Calrfornia Eastern Lab. Burlingame, Calif.
85911
Seamless Rubber Co. Chicago, Ill.
94144
Raytheon Mfg. Co., Industrial Components
98925 Clemte Transistor Prod,
000)0( 80/lode Electronics, Inc. Chicago 31, III.
86197
Clifton Pram,. Products Ctrflon Heights, Pa.
Drm, Receiving Tube Operation Quincy, Mass
Div. of Clevite Corp. Waltham, Mass.
09071 S.K. Smith Co. Los Angeles Pb. Calif.
86579 ?Precrsmn Rubber Products Corp. Dayton, Ohro
94145
Raytheon Mfg. Co., Semiconductor Div.,
98978 Internatronal Electronic
86684
Radio Corp. of America, RCA
Co Worn. Street Plant Newton, Mass
Research Cook Burbank, Calif.
Electron Tube Dry. Harrison, N.J.
94148
Scientrfic Radio Products. Inc.
99109 Columbia Technical Corp. New York, N.Y.
01730
Philco Corporation [Lansdale
Loveland, Colo
99313 Varian Associates Palo Alto, Calif.
Envision) Lansdale, Pa.
94154
Tung-Sol Electric. Inc. Newark, N.1
99515 Marshall Induslries, Eleclron
87473
Western Fibrous Glass Products Co.
One Francisco, Ca/d.
94197
Curtiss-Wright Corp.,
Electronics Div. East Paterson, N.1
Products Division Pasadena, Calif.
99707 Contr. Svertch Divisron, Controls Co.
8/014
Van Waters & Rogers Inc. Seattle, Wash.
90272
Soulhco Div. of S. Chesler Corp. Lester, Pa
al America El Segundo, Calif.
81930
Tower Mfg Corp Providence, R. I.
94315
Tru 01110 Prod. Div. or Model
99800 Delevan Electronics Corp. East Aurora, N.Y.
88140
Cullerdlanner. 300. LI000i4,
Engineering and tollg. Co. Chicago, Ill
99848 WrIco Corporation Indianapons, Ind.
88270
Gould-Nalronal Batteries. Inc. St. Paul. Minn.
94682
Worcester Pressed Aluminum Corp.
99934 Renbrandl, Inc. Boslon, Mass.
88698
General Mills, Inc. Buffalo, N.Y.
orcester, Mass.
99942 Hoffman Semiconduclor Dlv. ol
89231
Gi551), [141.111i: WC. Co Oakland, Calif.
95023
Plidbrick Researchers, Inc. Boston, Mass,
Hoffman Electronics Corp. Evanston, Ill.
894/3
General Electric Distribuling Corp.
95236
Allies Products Corp. M.., Fla.
99957 Technology Instr00en1 Corp
Schenectady. N.Y
95238
Continental Connector Corp. Woodside, N.Y.
of Ca.. Newbury Park, Calif.
00015-37
Revised: July 31, 1964
Fronn FSC Handbook Supplements
HR 1 Dated OCTOBER 1963
4 2 Dated MARCH 1962
Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
Appendix B
Model 410C
SALES AND SERVICE OFFICES IN THE U.S. AND CANADA
ALABAMA
Huntsville, 35801
Hewlett Packard
Southern Sales Division
Holiday Office Ctr., Suite 18
(205) 881-4591
TWX: 519-579-2204
ARIZONA
Scottsdale, 85251
Hewlett-Packard
Neely Sales Division
3009 No. Scottsdale Rd.
(602) 945-7601
TWX: 602-949-0111
Tucson, 85716
Hewlett-Packard
Neely Sales Division
232 So. Tucson Blvd.
(602) 623-2564
TWX: 602-792-2759
CALIFORNIA
Los Angeles Area
Hewlett-Packard
Neely Sales Division
3939 Lankershim Blvd.
North Hcllywood 91604
(213) 877-1282 and 766-3811
TWX: 910-499-2170
Sacramento, 95821
Hewlett-Packard
Neely Saes Division
2591 Carlsbad Ave.
(926) 482-1463
TWX: 916-444-8683
San Diego, 92106
Hewlett-Packard
Neely Sales Division
1055 Shafter Street
(714) 223-8103
TWX-714-276-4263
San Francisco Area
Hewlett-Packard
Neely Sales Division
501 Laurel Street
San Carlos 94071
(415) 591-7661
TWX: 910-376-4390
COLORADO
Englewood, 80110
Hewlett-Packard
Lahana Sales Division
7965 East Prentice
(303) 771-3455
TWX: 303-771-3056
CONNECTICUT
Middletown, 06458
Hewlett-Packard
Yewell Sates Division
589 Saybrook Rd.
(203) 346.6611
rwx: 203-346-7433
FLORIDA
Miami, 33125
Hewlett-Packard
Florida Sales Division
2907 Northwest 7th St.
(305) 635-6461
Orlando, 32803
Hewlett-Packard
Florida Sales Division
621 Commonwealth Ave.
1305) 425-5541
TWX, 305-275-1234
St. Petersburg, 33708
Hewlett-Packard
Florida Sales Division
410-150th Ave., Madeira Beach
(813) 391-0211
1WX: 813-391-0666
GEORGIA
Atlanta, 30305
Hewlett-Packard
Southern Sales Division
3110 Maple Drive, N. E.
(404) 233-114)
TWX: 810-751-3283
ILLINOIS
Chicago, 60645
Hewlett-Packard
Crossley Sales Division
2501 West Peterson Ave.
(312) 275-1600
TWX: 910-221-0277
INDIANA
Indianapolis, 46205
Hewlett-Packard
Crossley Sales Division
3919 Meadows Jr.
(317) 546.4891
TWX: 317-635-4300
KENTUCKY
Louisville, 402111
Hewlett-Packard
Southern Sales Division
Suite 4, 3411 Bardstown Rd.
(502) 459-4140
TWX: 810-535-3128
MARYLAND
Baltimore, 21207
Hewlett-Packard
Horman Sales Division
6660 Security Blvd.
(301) 944-5400
Washington, D. C. Area
Hewlett-Packard
Harman Sales Division
941 Rollins Avenue
Rockville 20852
(301) 427-7560
TWX: 710-828-9684
MASSACHusErrs
Boston Area
Hewlett-Packard
Yewell Sales Division
Middlesex Turnpike
Burlington 01804
(617) 272-9000
TWX: 710-332-03E2
MICHIGAN
Detroit, 48235
Hewlett-Packard
Crossley Sales 0-4ision
14425 West Eight Mile Road
(313) 342-5700
TWX: 313-342-0762
MINNESOTA
St. Paul, 55114
Hewlett-Packard
Crossley Sales Division
842 Raymond Avenue
16121 646-7881
TWX: 612-551-0055
MISSOURI
Kansas City, 64131
Harris-Hanson Company
7916 Paseo Street
(816) 444-9494
TWX: 816-556-2423
St. Louis, 63144
Harris-Hanson Company
2814 South Brentwood Blvd.
(314) 647-4350
TWX: 314-962-3933
NEW JERSEY
Asbury Park Area
Hewlett-Packard
Robinson Sales Division
Shrewsbury
(201) 747-1060
4011?161111iniviiIIIIISMINV
Englewood, 07631
Hewlett-Packard
RMC Sales Division
391 Grand Avenue
(201) 567-3933
NEW MEXICO
Albuquerque, 87108
Hewlett-Packard
Neely Sales Division
6501 Lomas Blvd., N. E.
(505) 255-5586
TWX: 505-243-8314
Las Cruces, 88001
Hewlett-Packard
Neely Sales Division
114 S. Water Street
(505) 526-2486
TWX: 505-524-2671
NEW YORK
New York, 10021
Hewlett-Packard
RMC Sales Division
236 East 75th Street
(212) 879-2023
TWX: 710-581-4376
Rochester, 14625
Hewlett-Packard
Syracuse Sales Division
800 Linden Avenue
(716) 381-4120
TWX, 716-221-1514
Poughkeepsie, 12601
Hewlett-Packard
Syracuse Sales Division
82 Washington St.
(9141 454-7330
TWX: 914-452-7425
Syracuse, 13211
Hewlett-Packard
Syracuse Sales Division
Pickard Bldg., E. Molloy Rd.
(315) 454-2486
T)NX: 315-477-1375
NORTH CAROLINA
High Point, 27262
Hewlett-Packard
Southern Sales Division
1923 N. Main Street
(919) 882-6873
TWX: 510-926-1516
OHIO
Cleveland, 44129
Hewlett-Packard
Crossley Sales Division
5579 Pearl Road
(216) 884-9209
TWX: 216-888-0715
Dayton, 45409
Hewlett-Packard
Crossley Sales Division
1250 W. Dorothy Lane
(513) 299-3594
TWX: 513-944-0090
PENNSYLVANIA
Camp Hill
Hewlett-Packard
Robinson Sales Division
(717) 737-6791
Philadelphia Area
Hewlett-Packard
Robinson Sales Division
144 Elizabeth Street
West Conshohocken 19428
(215) 248-1600 and 828-6200
TWX. 215-828-3847
Pittsburgh Area
Hewlett-Packard
Crossley Sales Division
2545 Moss Side Blvd.
Monroeville 15146
(412) 271-5227
TWX: 710-797-3650
TEXAS
Dallas, 75209
Hewlett-Packard
Southwest Sales Division
P.O. Box 7166, 3605 Inwood Rd.
1214r 357-1881 and 3326667
TWX: 910-861-4081
Houston, 77027
Hewlett-Packard
Southwest Sales Division
P.O. Box 22813, 4242 Richmond Ave.
(713) 667-2407
TWX: 713-571-1353
UTAH
Salt Lake City, 84115
Hewlett-Packard
Lahana Sales Division
1482 Major St.
(801) 486-8166
TWX: 801-521-2604
VIRGINIA
Richmond, 23230
Hewlett-Packard
Southern Sales Division
2112 Spencer Road
(703) 282-5451
TWX: 703-282-9986
WASHINGTON
Seattle Area
Hewlett-Packard
Neely Sales Division
11656 N. E. 8th St.
Bellevue 98004
(206) GL4-3971
TWX: 910-443-2303
CANADA
Montreal, Quebec
Hewlett-Packard (Canada) Ltd.
8270 Mayrand Street
(514) 735-2273
TWX: 610-421-3484
Ottawa, Ontario
Hewlett-Packard (Canada) Ltd.
1762 Carling Avenue
(613) 722-4223
TWX: 610-562-1952
Toronto, Ontario
Hewlett-Packard (Canada) Ltd.
1415 Lawrence Avenue, West
(416) 249-9196
TWX: 610-492-2382
HEWLETT it- PACKARD
001/04/20 : CIA-RDP70600584R000100280001-3
Model 410(.7 Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
INTERNATIONAL SALES AND SERVICE OFFICES
Appendix B
ARGENTINA
Mauricio A. Saurez
Telecommunicaciones
Carlos Calvo 224, Buenos Aires
Tel 30-6312
AUSTRALIA
Sample Electronics (Vic.) Pty. Ltd.
9-11 Cremorne Street
Richmond E. 1, Victoria
Tel: 42-4757 13 lines)
Sample Electronics (N.S.W.) Pty. Ltd.
4 Grose Street, Glebe, Sydney
New South Wales
Tel: 69-6338 (6 lines)
AUSTRIA
Unilabor G.m.b.H.
Rummelhardtgasse 6/3
Vienna
Tel: 426.181
BELGIUM
Hewlett-Packard Benelux S.A.
20-24 Rue de l'Hopital, Brussels
Tel: 11.22.20
BRAZIL
Ciental lmportacao E Comercio Ltda.
Rua Cons. Crispiniano, 69, 8. ? And.,
Conj. 81, Sao Paulo
Tel: 32-4332
CANADA
Hewlett-Packard (Canada) Ltd.
8270 Mayrand Street
Montreal, Quebec
(514) 735-2273
Hewlett-Packard (Canada) Ltd.
1762 Carling Avenue
Ottawa, Ontario
(613) 722-8162
Hewlett-Packard (Canada) Ltd.
1415 Lawrence Avenue W.
Toronto, Ontario
(416) 249-9196
CHILE
Hector Calcagni
Casilla 13942
Santiago
Tel: 6.42.26
DENMARK
Tage Olsen A/S
Ronnegade 1
Copenhagendb
Tel: 29.48.0
FINLAND
INTO 0/11
P. 0. Box 153
Meritullinkatu 11, Helsinki
Tel: 66.39.09 and 35.125
FRANCE
Hewlett-Packard France
150 Boulevard Massena
Paris 13e
Tel: 707.97.19
GERMANY
Hewlett-Packard V.m.b.H.
Steindamm 35, Hamburg
Tel: 24.05.51
Hewlett-Packard V.m.b.H.
Kurhessenstrasse 95
Frankfurt am Main
Tel: 52.00.36
IN EUROPE
Hewlett-Packard, S. A.
54 Route des Acacias
Geneva, Switzerland
Telephone: (022) 42.81.50
Telex: 2.24.86
Cable: HEWPACKSA
1-65
For
Hewlett-Packard V.m.b.H.
Reginfriedstrasse 13
Munich 9
Tel: 49.51.21/22
Hewlett-Packard Vm.b.H.
Technisches Niro
Herrenbergerstrasse 110
703 BOblingen, Wiirttemberg
Tel: 6971
GREECE
K. Karayannis
Klaftmonos Square, Athens 124
Tel: 230.301 15 lines)
INDIA
The Scientific Instrument Company, Ld.
6, Tej Bahadur Sapru Road, Allahabad 1
Tel: 2451
The Scientific Instrument Company, Ld.
240, Dr. Dadabhai Naoroji Road,
Bombay 1
Tel: 26-2642
The Scientific Instrument Company, Ld.
11, Esplanade East, Calcutta 1
Tel: 23-4129
The Scientific Instrument Company, Ld.
30, Mount Road, Madras 2
Tel: 86339
The Scientific Instrument Company, Ld.
B-7, Ajmeri Gate Extn., New Delhi 1
Tel: 271053
IRAN
Telecom Ltd.
P. 0. Box 1812, Tehran
Tel: 43850, 48111
ISRAEL
Electronics & Engineering Ltd.
16 Kremenetski St., Tel Aviv
Tel 35021 (3 lines)
ITALY
Hewlett-Packard Italiana S.p.A.
Viale Lunigiana 46, Milan
Tel: 69.15.84/5/6
Hewlett-Packard Italiana S.p.A.
Piazza Marconi, 25
Roma-Eur
Tel: 59.25.44/5
JAPAN
Yokogawa-Hewlett-Packard Ltd.
2270 Ishikawa-cho
Hachioji, Tokyo
Tel: Hachioji 0426-3-1231 (19 lines)
Yokogawa-Hewlett-Packard Ltd.
No. 3, 6-chome, Aoyama-Kitamachi
Akasaka, Minato-ku, Tokyo
Tel: 403-0073, 403-0074, 403-0075
Yokogawa-Hewlett-Packard Ltd.
No. 8, Umeda, Kita-ku, Osaka City
Tel: 361-3084, 341-2095
Yokogawa-Hewlett-Packard Ltd.
No. 4, 3-chome, Himeikedori,
Chigusa-ku, Nagoya City
Tel: 75-8545
KOREA
American Trading Company, Korea, Ltd.
112-35 Sokong-Dong
Seoul P. 0. Box 1103
Seoul
Tel: 3-7049, 3-7613
Sales and Service Assistance in Areas Not Listed
IN LATIN AMERICA
Hewlett-Packard Inter-Americas
1501 Page Mill Road
Palo Alto, California 94304, U.S.A.
Telephone: (415) 326-7000
TWX: 910-373-1267
Telex: 033811 Cable: HEWPACK
A, ? ? ? - ? S - - II I
NETHERLANDS
Hewlett-Packard Benelux N.V.
23 Burg Roellstraat, Amsterdam W.
Tel: (020) 13.28.98 and 13.54.99
NEW ZEALAND
Sample Electronics (N. Z.) Ltd.
8 Matipo Street
Onehunga S. E. 5, Auckland
Tel 565-361
NORWAY
Morgenstierne & Co. A/S
IngeniOrfirma
6 Wessels Gate, Oslo
Tel: 20 16 35
PORTUGAL
Telectra
Rua Rodrigo da Fonseca 103
P. 0. Box 2531
Lisbon 1
Tel: 68 60 72 and 68 60 73 and 68 60 74
PUERTO RICO & VIRGIN ISLANDS
San Juan Electronics, Inc.
150 Ponce de Leon, Stop 3
P. 0. Box 5167
Pta. de Tierra Sta., San Juan 00906
Tel: 722-3342, 724-4406
SPAIN
ATAIO, lngenieros
A. Aguilera, No. 8, Madrid 15
Tel: 223.27.42, 223.41.71, and 224.84.97
SOUTH AFRICA
F. H. Flanter & Co. (Pty.), Ltd.
Roselle House
Buitencingle Street, Cape Town
Tel: 3-3817
SWEDEN
H-P Instrument AB
Centralvagen 28, Solna Centrum
Tel: 08-83.08.30 and 10-83.08.30
SWITZERLAND
Max Pual Frey
Wankdorffeldstrasse 66, Bern
Tel: (031) 42.00.78
TAIWAN (FORMOSA)
Hwa Sheng Electronic Co., Ltd.
21 Nanking West Road, Taipei
Tel: 4-6076, 4-5936
TURKEY
TELEKOM Engineering Bureau
P.O. Box 376-Galata, Istanbul
Tel: 49.40.40
UNITED KINGDOM
Hewlett-Packard Ltd.
Dallas Road
Bedford, England
Tel: Bedford 68052
VENEZUELA
Citec, C. A.
Edif. Arisan-Of #4
Avda. Francisco de Miranda-Chacaito
Apartado del Este 10.837, Caracas
Tel: 71.88.05
YUGOSLAVIA
Belram S.A.
83 Av. des Mimosas
Brussels 15, Belgium
Tel: 35.29.58
Contact:
ELSEWHERE
Hewlett-Packard
International Marketing Department
1501 Page Mill Road
Palo Alto, California 94304, U.S.A.
Telephone: (415) 326-7000
TWX. 910-373-1267
Telex: 033811 Cable: HEWPACK
rso- s:As :Arose is
Apperf1RxTved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
MANUAL BACKDATING CHANGES
MODEL 410C
ELECTRONIC VOLTMETER
Manual Serial Prefixed: 433
/7, Part No. 410C-903
To adapt this manual to instruments with other serial prefixes check for errata below, and make
changes shown in tables.
NOTE
This manual backdating sheet makes this manual applicable to earlier instru-
ments. Instrument-component values that differ from those in the manual,
yet are not listed in the backdating sheet, should be replaced using the stock
number given in the manual.
tristrument Serial Prefix Make Manual Changes
4.33 Manual Applies
344 L.2, 3
3_3') 1, 2, 3, 4
323 1, 2, 3, 4, 5
CHANGE #1
CHANGE #2
CHANGE #3
Instrument Serial Prefix
Model 410C
Make Manual Changes
311
1, 2, 3, 4, 5, 6
NOTE
No. and (A,A)Stock No. are synonymous.
Under Table of Replaceable Parts:
Delete: A3R20; Resistor, fixed, 1 K ohm; #Part No. 0687-1021.
Add: A3R20; Resistor, fixed, 10 K ohms; ',p)Part No. 0686-1035.
Figure 5-10, Amplifier Schematic, change:
A3R20 from 1 K ohm to 10 K ohms.
NOTE
Inter Models 410C (Serial Prefix 433 and
,)ove) use a 1 K ohm resistor for A3R20 to
increase the meter zero adjustment (A3R21).
!i recommended that earlier models be
modified accordingly, in case of zero adjust-
ment problem. Refer to V: Service Note
410C-1 for modification instructions.
Under Table of Replaceable Parts:
Delete: Ql; Transistor, PNP Germanium; i. Part No. 1850-0098.
Add: Qi; Transistor, PNP Germanium; 4i Part No. 1850-0094.
NOTE
; :Iter Models 410C (Serial Prefix 433 and
a)ove) use the *Part No. 1850-0098 for in-
.11ased reliability. It is recommended
bat earlier models be modified accordingly,
in case of failure of the earlier type transistor.
li'efer to Service Note 410C-3 for modifica-
ion instructions.
Under Thole of Replaceable Parts:
Delete CR7; Diode, Breakdown Junction, 9 v, 1. 5 w; 14 Part No. 1902-0327.
Add: A7CR7; Diode, Breakdown Junction, 9 v, 0.4 w; 171 Part No. 1902-0037.
Figure 5-8, Power Supply Schematic, change:
CR7 to A7CR7. This designates that this diode is part of the Power Supply
As.;embly, A7.
NOTE
Later Models 410C (Serial Prefix 433 and
aiiove) use the 1.5 watt breakdown diode ('Ap;
Part No. 1902-0327) for increased relia-
bllity. It is recommended that earlier models
iro modified accordingly, in case of failure of
the 0.4 watt diode. Refer to hp Service Note
410C-2 for modification instructions.
Supplement B for
Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3 410C-903
roved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3
Model 410PP Manual Backdating Changes Model 410C Page 2
Instrument Serial Prefix Make Manual Changes
433
Manual Applies
344
1,
2,
3
339
1,
2,
3,
4
328
1,
2,
3,
4,
5
CHANGE #4
CHANGE #5
CHANGE #6
Appendix C
Instrument Serial Prefix Make Manual Changes
311
1, 2, 3, 4, 5, 6
Under Table of Replaceable Parts:
Delete: S3; Switch, pushbutton w/pilot light; V Part No. 3101-0100.
Delete: DS1; Light, indicator, A1C neon; V Part No. 1450-0106.
Delete: R5; Resistor, fixed, 68 K ohms; Part No. 0687-6831.
Add: S3; Switch, pushbutton; Part No. 3130-0054.
Add: DS1; Light, indicator, NE-2H neon; V Part No. 1450-0048.
Add: Bushing, panel; V Part No. 5020-0883.
Add: Actuator; AC switch; V Part No. 5040-0918.
Add: Bracket; AC switch; V Part No. 410C-12C.
Add: R5; Resistor, fixed, 33 K ohms; V Part No. 0687-3331.
NOTE
Later Models 410C (Serial Prefix 344 and
above) use the V Part No. 3101-0100, push-
button switch w/pilot light for increased re-
liability. It is recommended that this im-
proved switch-pilot light assembly be used
for replacement, in case of failure of the
older type switch. Refer to V Service Note
P-3101-0100 for modification instructions.
Under Table of Replaceable Parts:
Delete: A3R3; Resistor, fixed, 100 ohms; V Part No. 410C-26D.
Add: A3R4; Resistor, fixed, 94 ohms; V Part No. 0727-0470.
Add: A3R6; Resistor, fixed, 6 ohms; V Part No. 410C-26C.
Figure 5-10, Amplifier Schematic, change:
RIO AMP L. ASSY.
A3
PIN 4
Under Table of Replaceable Parts:
Delete: A1R7; Resistor, fixed, 15K ohms; V Part No. 0687-1531.
Add: A1R7; Resistor, fixed, 22 K ohms; V Part No. 0758-0020.
Delete: A2R2; Resistor, fixed, 10. 5 ohms; V Part No. 0727-0955.
Add: A2R2; Resistor, fixed, 6 megohms; V Part No. 0727-0460.
Delete: A2R10; Resistor, fixed, 6 megohms; V Part No. 0730-0176.
Add: A2R10; Resistor, fixed, 10.8 ohms; V Part No. 0728-0005.
Figure 5-13, RANGE and FUNCTION Switching (Pictorial), change:
A1R7 from 15 K ohms to 22 K ohms.
A2R2 from 10. 5 ohms to 6 megohms.
A2R10 from 6 megohms to 10.8 ohms.
Supplement B for
410C-903
Approved For Release 2001/04/20 : CIA-RDP70600584R000100280001-3